CTS CVT-3512 Series Посібник користувача
Переглянути онлайн або завантажити pdf Посібник користувача для Конвертер мультимедіа CTS CVT-3512 Series. CTS CVT-3512 Series 2 сторінки. 10/100/1000base-t to 1000base-x standalone managed media converter with 802.3ah oam compliance
Друкувати сторінку
Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in
any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.
FCC Warning
The CVT-3512 Series have been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These standards are designed to provide
reasonable protection against harmful interference when these
devices are operated in a commercial environment. These
devices generate, use, and can radiate radio frequency energy
that may cause harmful interference to radio communications
unless installed in accordance with this User's Guide.
Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.
This is a lead-free and RoHS-compliant product.
1. Checklist
The package should contain the following items:
- CVT-3512 Converter
- AC-DC Power Adapter
- CD (User's Guide & MIB file)
Please notify your sales representative immediately if any items
are missing or damaged.
2. Overview
CVT-3512 Series are designed to meet the increasing needs for
Gigabit network deployment and are able to extend a
copper-based Gigabit network via fiber cable to a maximum
distance up to 80KM.
CVT-3512 Series are fully compliant with IEEE 802.3, 802.3u,
802.3ab & 802.3z standards. It can be installed into a CVT
Converter RACK. The installation and operation procedures are
simple and straightforward.
Operation status can be locally
monitored through a set of Diagnostic LED indicators located in
the front panel.
Major Features:
- Auto-Negotiation in TX port
- MDI/MDIX Auto-Crossover supported
- Support Flow Control
- Support Link Alarm
- Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
- Support Selectable ISP Ethernet Tag Type
- Q-in-Q Double Tag configuration
- Support DHCP Client
- Support SNMP / Web Management interface
- Support SNMP v1 and v2c
- Support HTTP Firmware Upgrade
- Support Power Down Trap Management
3. Installation
- Attach fiber cable from the CVT-3512 to the fiber network.
The fiber connections must be matched – transmit socket to
receive socket.
- Attach a UTP cable from the 10/100/1000BASE-T network
to the RJ-45 port on the CVT-3512.
- Connect the power adapter to the CVT-3512 and check
whether the Power LED indicator lights up. The TX Link/Act
and FO Link/Act LED indicator will light up when all the
cable connections are satisfactory.
Figure 1. CVT-3512 Dual-Fiber Front Panel
Figure 2. CVT-3512 Single-Fiber & SFP Front Panel
Figure 3. CVT-3512 Series Rear Panel
4. DIP SWITCH Setting
The factory default setting for PIN 1 and PIN 5 is ON. The rest of
Pins are OFF.
Pin NO.
Function
TX
1
Auto-Negotiation
Manual TX Data
2
Rate 10M/100M
Manual TX Data
3
10M or 100M
Rate 1000M
4
Flow Control
Fiber
5
Auto-Negotiation
6
Reserve
7
Link Alarm
8
TP Configuration
From S/W
Press once for Loopback test.
Diag
Press for 10 seconds to restore factory default
button
setting.
NOTE: Before changing Data Rate and Duplex mode setting,
please make sure Auto-Negotiation is disabled.
Diag
Diag
OFF
ON
Disable
Enable
10M
100M
1000M
Disable
Enable
Force
Enable
Always OFF
Disable
Enable
From DIP