3Com OfficeConnect 3C857 Посібник з монтажу
Переглянути онлайн або завантажити pdf Посібник з монтажу для Шлюз 3Com OfficeConnect 3C857. 3Com OfficeConnect 3C857 2 сторінки. Cable/dsl gateway
Друкувати сторінку
Installation Guide
OfficeConnect
®
Cable/DSL Gateway
(3C857)
3Com Corporation, Corporate Headquarters, 5400 Bayfront Plaza, Santa Clara, CA 95052-8145
Copyright © 2002 3Com Corporation. All rights reserved. 3Com, the 3Com logo, and OfficeConnect
are registered trademarks of 3Com Corporation.
Microsoft, MS-DOS and Windows are registered trademarks of Micorsoft Corporation.
All other company and product names may be trademarks of their respective companies.
Part number: DIA0085-5AAA02 Published: August 2002
INTRODUCTION
About This Guide:
This Guide takes you through the basic steps necessary to install and configure
your OfficeConnect Cable/DSL Gateway, and establish a connection from your
computers to the Internet. Throughout, the OfficeConnect Cable/DSL
Gateway is simply referred to as the Gateway.
Your package contains:
One OfficeConnect Cable/DSL Gateway
One power adapter for use with the Gateway
Four rubber feet
One Ethernet cable
One CD-ROM containing the Gateway Discovery program and the User Guide
This Installation Guide
One Support and Safety Information Sheet
One Warranty Flyer
System Requirements
Before starting, you must ensure the following:
You already have a cable or DSL broadband connection to the Internet, with
a suitable modem, and that this connection works properly. The modem
must have an Ethernet port for connection to your Gateway.
You have a computer that has an Ethernet connection available and is
already correctly configured for communication with the Internet. Your
computer must be able to connect to the Internet via the modem, and must
have a Web browser installed.
There are no other DHCP server devices on your local network that are
responsible for allocating IP addresses to your computers and other network-
connected devices. Your Gateway will now perform this function by default.
If one or more of these conditions are not met, refer to the comprehensive
Gateway User Guide provided on the accompanying CD-ROM for further guidance.
ABOUT YOUR GATEWAY
Cable/DSL Gateway - Front
1
2
3
4
LAN Status
Cable/DSL
Alert
1 Alert LED
Flashing slowly - The Gateway has completed the
Reset to Factory Defaults process, and is waiting for
orange
you to reset the unit. To do this, remove power, wait
Indicates a number of different conditions, as
10 seconds and then re-apply power. The Gateway
described below.
will then enter the start-up sequence and resume
Off - The Gateway is operating normally.
normal operation.
Flashing quickly - Indicates one of the following
On for 2 seconds, and then off - The Gateway has
conditions:
detected and prevented a hacker from attacking your
network from the Internet.
• The Gateway has just been started up and is
running a self-test routine, or
Continuously on - A fault has been detected with
your Gateway during the start-up process. Refer to
• The administrator has invoked the Reset to Factory
the main User Guide.
Defaults command, or
2 Power LED
• The system software is in the process of being
upgraded
green
In each of these cases, wait until the Gateway has
Indicates that the Gateway is powered on.
completed the current operation and the alert LED
is Off.
DIMENSIONS AND STANDARDS
Dimensions and Operating Conditions
Standards
Functional:
ISO 8802/3
EMC:
IEEE 802.3, 802.3u
Safety:
UL 1950, EN 60950
CSA 22.2 #950,
IEC60950
Environmental:
* Refer to Regulatory Notices section in the Support and Safety Information sheet
Cable/DSL Gateway
7 VA, 23.9 BThU/hr
power requirement
0 to 40ºC (32 to 105ºF)
operating
temperature
0 to 90%
(non-condensing)
humidity
Cable/DSL Gateway
535g (1.3 lb)
Cable/DSL Gateway - Rear
3C857
OfficeConnect Cable/DSL Gateway
3 Four LAN Status LEDs
green (100Mbps link) / yellow (10Mbps link)
If the LED is on, the link between the port and the
next piece of network equipment is OK. If the LED is
flashing, the link is OK and data is being transmitted
or received. If the LED is off, nothing is connected, or
the connected device is switched off, or there is a
problem with the connection (refer to the 'Problem
Solving' section). The port will automatically adjust to
the correct speed and duplex.
4 Cable/DSL Status LED
green (100Mbps link) / yellow (10Mbps link)
If the LED is on, the link between the Gateway and
the cable or DSL modem is OK. If the LED is flashing,
the link is OK and data is being transmitted or
received. If the LED is off, nothing is connected, the
modem is switched off or there is a problem (refer to
the "Problem Solving" section).
POSITIONING YOUR GATEWAY
Safety Information
WARNING: Please read the 'Important Safety Information' section in the
EN 55022 Class B
Support and Safety Information sheet before you start.
EN 55024
VORSICHT: Bitte lesen Sie den Abschnitt 'Wichtige
FCC Part 15 Class B*
Sicherheitsinformationen' sorgfältig durch, bevor Sie das Gerät einschalten.
ICES-003 Class B
VCCI Class B
AVERTISSEMENT: Veuillez lire attentivement la section "Consignes
CNS 13438 Class A
importantes de sécurité" avant de mettre en route.
EN 60068 (IEC 68)
When positioning your Gateway, ensure:
It is out of direct sunlight and away from sources of heat.
Cabling is away from power lines, fluorescent lighting fixtures, and
sources of electrical noise such as radios, transmitters and broadband
amplifiers.
Water or moisture cannot enter the case of the unit.
Air flow around the unit and through the vents in the side of the case
is not restricted. We recommend you provide a minimum of 25mm
(1in.) clearance.
Using the Rubber Feet
Use the four self-adhesive rubber feet to prevent your Gateway from
moving around on your desk or when stacking with other flat top
OfficeConnect units. Only stick the feet to the marked areas at each
corner of the underside of your Gateway.
5
6
Ethernet
Cable/
4
DSL
5 Power Adapter socket
Only use the power adapter that is supplied with
this Gateway. Do not use any other adapter.
6 Ethernet Cable/DSL port
The Ethernet Cable/DSL port is configured as MDI,
for connection to your modem with the supplied
straight-through patch cable. The port will
automatically adjust to the correct speed and
duplex.
7 Four 10/100 LAN ports
Using a suitable RJ-45 cable, you can connect your
Gateway to a computer, or to any other piece of
equipment that has an Ethernet connection (for
example, a hub or a switch). The LAN ports are
configured as MDIX, for connection to a computer
with a straight through RJ-45 cable.
7