ACORN AQUA A511110P Інструкції з монтажу, експлуатації та технічного обслуговування - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкції з монтажу, експлуатації та технічного обслуговування для Диспенсер для води ACORN AQUA A511110P. ACORN AQUA A511110P 8 сторінок. Aquacold series compact free standing water coolers
Друкувати сторінкуIMPORTANT:
1. Waste P-Trap, Water Supply Service Angle Stop Valve and 2" x 4" Electrical Plug-In Receptacle
to be supplied by others in accordance with local codes. A metallic p-trap must be used for the
drain connection.
2. Provide 4" minimum clear space on fixture sides to allow for proper ventilation through cabinet
louvers.
3. Water supply is 3/8" Outer Diameter copper tube. Waste is 1-1/4" Outer Diameter.
4. Completely flush supply lines of all foreign debris before connecting to fixture. W ater cooler
designed to not cause problems with taste, odor, color, or sediment. Optional water filter (Wf1),
is available should any of these problems arise from the water supply.
5. Do NOT solder tubes inserted into the strainer as damage to the o-ring may result.
6. All burrs must be removed from outside of cut tubes before inserting into strainer or other
components.
7. Power supply must be identical in voltage, cycle and phase to that specified on the cooler data
plate. Electrical outlet and furnished power cord with plug must be used to supply power to
fixture. Do NOT wire compressor directly to the power supply.
8. This unit must be grounded per the requirements of applicable electrical codes.
9. WARNING: Warranty is voided if installation is not made following current Acorn Aqua
installation instructions and if components are assembled to the fixture that is not approved by
Acorn Aqua.
10. Fixture operates within water pressure range of 20 to 105 psig. Acorn Aqua will not warranty
fixtures damaged when connected to supply lines with flow pressure lower than 20 psig or
higher than 105 psig. A pressure regulator must be furnished by others on supply line if inlet
pressure is greater than 105 psig.
11. Due to cold waste water, Acorn Aqua recommends that p-trap supplied by installer be insulated
to prevent excessive condensation.
12. Per UPC 609.10- All building water supply systems in which quick acting valves are installed
shall be provided with devices to absorb the hammer caused by high pressure resulting from the
quick closing of the valve. These pressure-absorbing devices shall be approved mechanical
devices. Water pressure-absorbing devices will be installed as close as possible to the quick
closing valve.
INSTALLATION:
Provide rough-ins as shown in Roughing-In and Dimensional Drawing.
2. Anchor water cooler to wall through anchor clips on the bottom of the base.
3. Remove the front panel from the water cooler by taking out the screws on each side at the
bottom front, press the panel sides together at the bottom so that front panel clips disengage
from the housing sides and carefully pull forward and down. Set panel aside in a safe place
where it will not be damaged.
5. After thoroughly flushing the 3/8" o.d. supply line, connect water supply to water cooler .
6. Make up 1-1/4" o.d. p-trap waste connection.
START UP:
1. Before connecting power supply and assembling bottom cover to water cooler , but after thoroughly
flushing the supply line and connecting it to the fixture, turn on building water supply and check all
connections for leaks.
2. Air within the water cooler system or the structure supply piping will cause an irregular bubbler
outlet stream until purged out by incoming water. Covering the bubbler with a clean cup (or
similar object) is recommended when first activating water cooler to prevent excessive
splashing. Depress a side or front push bar until steady water stream is achieved
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered
on the underside of the fixture in the knee clearance area up to the flow regulator . Turning
clockwise will increase flow and turning counterclockwise will decrease flow .
4. Recheck all water and drain connections with water flowing through system.
L1001054
Page 3 of 8
Revised: 07/27/10