Dirt Devil ND20500 Посібник користувача - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник користувача для Повітродувка Dirt Devil ND20500. Dirt Devil ND20500 8 сторінок.

Друкувати сторінку

ELECTRICAL CONNECTION CONT.

Tool's

Cord Size in A.W.G.

Amperage

Cord Length in Feet

Rating

25 50 100 150

3-6

18 16

6-8

18 16

8-10

18 16

10-12

18 16

12-16

14 12

WARNING:

Keep the extension cord clear of the working area. Position the cord so that it will not get

caught on lumber, tools, or other obstructions while you are working with a power tool.

Failure to do so can result in serious personal injury.

WARNING:

Check extension cords before each use. If damaged replace immediately. Never use prod-

uct with a damaged cord since touching the damaged area could cause electrical shock

resulting in serious injury.

• When working outdoors with a product, use an extension cord that is designed

for outside use. This type of cord is designated with "W-A" or "W" on the cord's

jacket. Before using any extension cord, inspect it for loose or exposed wires and

cut or worn insulation.

CONNECTING THE POWER CORD TO THE

EXTENSION CORD

Secure the extension cord (A) Fig.2 to the

extension cord lock (B) on the motor housing.

First bend the end of the extension cord and

then pass it through the cord lock opening

(C). Then slip the extension cord around the

"T" notch cord lock (B) and pull on the exten-

sion cord to get a tight fit. This will prevent

accidental unplugging of the extension cord

during use. Then plug the female end of the

extension cord into the tool's polarized plug.

WARNING! To reduce risk of electric shock, do

not expose to rain, do not use on wet sur-

faces. Store indoors.

NOTE: Servicing of a product with double insu-

lation requires extreme care and knowledge

of the system and should be performed only by a qualified service technician. For

service, we suggest you return the tool to your nearest authorized service center

for repair. Always use original factory replacement parts when servicing.

Figure 1

Figure 2

HOW TO ASSEMBLE CONT.

WARNING:

Do not attempt to modify this product or create accessories not recommended for use with

this product. Any such alteration or modification is misuse and could result in a hazardous

condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result

in accidental starting and possible serious personal injury.

VACUUM/MULCHER MODE

WARNING! The vacuum/mulcher inlet and outlet both have a built-in limit switch

which prevents the vacuum/mulcher from starting if the main collection tube

(A) Fig.5 and the collection bag attachment (C) are not installed or not installed

properly. Make sure the vacuum/mulcher main collection tube and the collection

bag attachment are installed before attempting to use the vacuum/mulcher.

In vacuum/mulcher mode, the main collection tube (A) Fig.5, lower sectioncollec-

tion tube (B) and the collection bag attachment (C) with collection bag must be

installed. First, remove the blower inlet safety guard (A) Fig.4 (if installed). Then

install the main collection tube (A) to the vacuum/mulcher inlet, position the main

collection tube over the vacuum/mulcher inlet, rotate the collection tube ap-

proximately 90 degrees. Make sure the collection tube has engaged the vacuum/

mulcher inlet grooves, at this point you must not be able to lift the collection tube

upwards. Make sure the limit switch actuator engages the inner limit switch, then

lock the collection tube using the locking clip (refer to "B" & "C" Fig.4).

Install the lower section collection tube (B) Fig.5 to the main collection tube (A).

Align the grooves on both collection tubes and push them together until they click

into position.

Then install the collection bag and attachment (C) Fig.5 to the vacuum/mulcher

outlet (D). Align the grooves on the collection bag attachment with the grooves on

the vacuum/mulcher outlet. Push the collection bag attachment onto the vacuum/

mulcher outlet until it clicks into position. Attach the collection bag buckle to the

clip on the lower section collection tube. The vacuum/mulcher is now ready to

use, make sure you have read and understood the safety and operation instruc-

tions before using.

It is recommended to install the adjustable shoulder strap (D) Fig.3 to the vacuum/

mulcher handle (E).