Cub Cadet Commercial Hydraulic Renovator Посібник оператора - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник оператора для Газонна та садова техніка Cub Cadet Commercial Hydraulic Renovator. Cub Cadet Commercial Hydraulic Renovator 12 сторінок. Kawasaki, 8hp engine

Друкувати сторінку

OPERATING INSTRUCTIONS

The tension of the pump drive belt should be ad-

justed so that a five-pound pull between the engine

pulley and the pump pulley deflects the belt about

3/16 inch. Tighten the pump mounting bolts. Final-

ly, readjust the position of the control cable in the

lower handle.

d. Replace the belt safety cover.

Check the tension of the traction drive chain.

Raise the rear end of the power deck off the

ground.

Press in on the traction drive chain between the

drive sprocket on the hydraulic motor and the driv-

en sprocket on the differential. The chain should

deflect 3/16 inch. To adjust the tension in this

chain, the hydraulic motor must be moved. Loosen

the four mounting bolts which hold the motor to its

mounting bracket and pivot the motor to the proper

position and tighten the four mounting bolts.

While the traction drive chain is exposed oil it light-

ly with clean engine oil.

Lower the rear end of the Renovator back to the

ground.

Oil all of the wear points listed in the maintenance

section.

C. Break-In and Operation

Make certain you thoroughly understand all of the safety

precautions before you attempt to operate this machine.

Check the hydraulic oil level. When filling the tank, stop

when the oil reaches one inch from the top. This space

must be left for expansion. Use 1OW-40 engine oil.

Check the engine oil level. Fill to the proper level with

1OW-40 engine oil rated for service SE or SF.

Before moving the Renovator, set the slicer depth

adjusting lever so that the slicer reel is in the fully raised

position. Then, shift the hydraulic traction control lever to

forward if you wish to push the machine forward or hold

it in reverse if you wish to pull the Renovator to the rear.

Push the Renovator outdoors. Check the engine

gasoline level. When filling the tank, stop when the

gasoline reaches one inch from the top. Use fresh,

clean, unleaded, regular gasoline.

Push the Renovator to a "test area" where you can

operate and become familiar with the Renovator for

about half an hour without being disturbed.

Set the slicing/dethatching depth using the slicer depth

adjustment lever. (The blades should just graze the

ground for dethatching and should slice the ground for

seeding.)

(In actual operation, you would perform the following

procedure. For practice, however, it is not necessary to

load the seed hopper.) Set the seed flow adjustment dial

at the desired seed flow rate. The settings for common

types of seed at various seeding rates are shown in the

table on page 6. Load the seed hopper.

DANGER:

started in forward or reverse. Do not start

engine unless traction control is in neu-

tral.

Start the engine:

Do not let anyone touch the slicer safety clutch.

Shift the hydraulic traction control lever to neutral.

Connect the spark plug wire.

Open the fuel shutoff valve.

Turn the engine on/off switch to on.

Pull the engine choke to the closed position.

Move the throttle lever halfway between slow and

fast.

Grasp the starter grip and pull slowly until the start-

er engages and then pull the cord rapidly to over-

come compression, prevent kickback and start the

engine. Allow the cord to recoil slowly. Repeat if

necessary with the choke opened slightly.

Push the engine choke to the half open position

and allow the engine to warm up. Then, open the

choke all the way and move the throttle lever to

fast.

10. Slowly move the hydraulic traction control lever in the

"Forward" direction and the Renovator will start to move

forward. Open the seed flow lever by pushing it forward.

Use the hydraulic traction control lever to adjust the

forward speed.

11. Push down on the handle to lift the front wheels off the

ground and pull the slicer safety clutch down with your

left hand and hold it against the handle and the slicer

reel will start to rotate. Now raise the handle to lower the

front wheels and ease the slicer reel into the ground.

12. Operate the Renovator in a straight line. Before you

have reached the end of the first pass, use the hydraulic

traction control lever to slow your rate of travel, close the

seed flow lever and press down on the handle to lift the

rotating slicer reel out of the ground. (Note: The slicer

reel will not stop rotating unless you release the slicer

safety clutch with your left hand.) Turn the Renovator

around 180 degrees. Line up the Renovator for a proper

overlap, raise the handle easing the slicer reel back into

the ground, open the seed flow lever and start the

second pass, resuming normal operating speed. For

best results, renovate each area in two directions, 90

degrees apart, at 1/2 the total seeding rate.

13. When renovating an area surrounded by walkways or

driveways, make at least two complete passes around

the perimeter. This will provide enough room to make

turns at the end of each pass without running the slicer

blades into the concrete or asphalt.

14. Practice operating the Renovator for at least one-half

hour and then close the seed flow lever, release the

slicer safety clutch and move the hydraulic traction

control lever to "Neutral". Set the slicer depth adjusting

lever to the transport position, move the hydraulic

traction control lever in the "Forward" direction and

return the machine to the shop.

Can cause injury or damage if