Abbott CentriMag Короткий довідник

Переглянути онлайн або завантажити pdf Короткий довідник для Медичне обладнання Abbott CentriMag. Abbott CentriMag 2 сторінки. Circulatory support system alarms and alerts

Друкувати сторінку

CentriMag

Circulatory Support System

Alarms and Alerts Quick Reference Guide

Alarm/

Text Mes-

System Status & OperatorResponse

Alert

sage

The Pump will not start. An audible alarm will sound, which

cannot be muted. Switch the Console OFF and ON again. If

POWER ON

Alarm

the alarm reappears, switch to the backup Console, Motor

TEST FAIL

and Flow Probe, record the alarm message and contact

your local Abbott Medical representative.

The Pump will stop. An audible alarm will sound, which

SYSTEM

cannot be muted. Clamp the return tubing and switch to

FAULT

the backup Console, Motor and Flow Probe according the

Alarm

(Run-Time

procedure described in Section 2. Resume support. Record

System

the alarm message and contact your local Abbott Medical

Failure)

representative.

The Pump will stop. An audible alarm will sound, which

can be muted for 60 seconds.Clamp the return tubing

MOTOR

and switch to the backup Console, Motor and Flow Probe

Alarm

STOPPED

according the procedure described in Section 2. Resume

support. Record the alarm message and contact your local

Abbott Medical representative.

The Pump will stop. An audible alarm will sound, which can

be muted for 60 seconds.

During setup of the System:

Press the alarm acknowledge button and check that the Mo-

tor connector is fully inserted into the back of the Console.

During support:

MOTOR

Press the alarm acknowledge button and check that the

Alarm

DISCON-

connector of the Motor is fully inserted into the back of the

NECTED

Console. Resume support. If the visual alarm message

does not disappear, clamp the return tubing and switch to

the backup Console, Motor and Flow Probe according the

procedure described in Section 2. Resume support. Record

the alarm message and contact your local Abbott Medical

representative.

System will not start. An audible alarm will sound, which can

be muted for 60 seconds. Press the alarm acknowledge

PUMP NOT

button. Insert or reinsert the pump and secure it with

Alarm

INSERTED

the locking screw. If the alarm repeats, switch to backup

Console, Motor and Flow Probe according the procedure

described in Section 2.

An audible alarm will sound and the System will continue

to operate. Press the alarm acknowledge button, if the

visual alarm message does not disappear, clamp the return

MOTOR

Alarm

tubing, stop the pump and switch to the backup Console,

ALARM

Motor and Flow Probe according the procedure described

in Section 2. Resume support. Record the alarm message

and contact your local Abbott Medical representative.

Check the Pump flow. If pump flow is satisfactory, reduce

set speed while insuring that flow is maintained. Press

the alarm acknowledge button. If the alert repeats, clamp

the return tubing, stop the pump and switch to the backup

Console, Motor and Flow Probe according the procedure

SET PUMP

described in Section 2. Resume support. Record the alert

Alert

SPEED NOT

message and contact your Abbott Medical representative.

REACHED

If the pump flow is not satisfactory, clamp the return tubing

and switch to the backup Console, Motor and Flow Probe

according to the procedure described in Section 2. Resume

support. Record the alert message and contact Abbott Med-

ical representative.

RESPONSE TO SYSTEM ALARMS OR ALERTS

When a System alarm or alert condition occurs, an alarm or alert tone sounds and

text message appears on the display of the 2nd Generation CentriMag Primary

Console. Most alarms and alerts require some action on the user's part to correct

the cause. The following table can be used to determine how to respond to an

alarm or alert condition.

Alarm/

Text Mes-

System Status & OperatorResponse

Alert

sage

The Console battery will not function. An audible alarm

BATTERY

will sound. Switch to the backup Console, Motor and Flow

Alert

MODULE

Probe according to the procedure described in Section 2.

FAIL

Resume support. Record the alert message and contact

your Abbott Medical representative.

The Pump will stop after a very short time. Plug the Console

BATTERY

into a AC power outlet to charge the battery. If no AC outlet

Alert

BELOW

is available, switch to the backup Console, Motor and Flow

MINIMUM

Probe according to the procedure described in Section 2.

Resume support.

Check the Flow Probe connection on back of the Console.

FLOW

If necessary, reconnect the Flow Probe connector to the

PROBE

Alert

back of the Console. Press the alarm acknowledge button.

DISCON-

Switch to the backup Flow Probe, if the alert message

NECTED

repeats.

Press the alarm acknowledge button, if the message does

not disappear, clamp the return tubing, stop the pump

SYSTEM

and switch to the backup Console, Motor and Flow Probe

Alert

ALERT

according the procedure described in Section 2. Resume

support. Record the alert message and contact your local

Abbott Medical representative.

Manually disconnect, reposition and reconnect the

FLOW

Flow Probe transducer to the tubing. Press the alarm

SIGNAL

acknowledge button. Switch to the backup Flow Probe,

INTER-

if the alert message repeats. If problem still persists after

Alert

RUPTED

switching to the backup Flow Probe, stop the pump and

(Flow rate

switch to a backup Console. Follow the instructions

sensor error)

described in Section 2. Resume support. Record the alert

message and contact your Abbott Medical representative.

FLOW

Check for physiologic cause or circuit obstruction.

BELOW

Check minimum flow set point. Do not increase RPM

Alert

MINIMUM

without confirming that adequate blood volume is available.

(Low Flow)

Common cause of this alert is inadequate blood volume at

the drainage cannula site for the desired pump flow.

FLOW

Alert

ABOVE

Reduce Pump speed and check for cause.

MAXIMUM

Check the electrical connections on the pressure 1 trans-

PRESSURE

ducer and recalibrate. If the problem persists disconnect,

Alert

1 DISCON-

reconnect, and recalibrate the transducer. Consider chang-

NECTED

ing the transducer and cable if the problem persists.

Check the electrical connections on the pressure 2 trans-

PRESSURE

ducer and recalibrate. If the problem persists disconnect,

Alert

2 DISCON-

reconnect, and recalibrate the transducer. Consider chang-

NECTED

ing the transducer and cable if the problem persists.

Alarm/

Text Mes-

System Status & OperatorResponse

Alert

sage

The pressure monitoring system will not function. If pressure

monitoring is needed then change to the backup Console,

PRESSURE

Motor and Flow Probe. Switch to the backup System

Alert

SYSTEM

according the procedure described in Section 2. Resume

FAIL

support. Record the alert message and contact your Abbott

Medical representative.

Check for and resolve a physiological or mechanical cause.

PRESSURE

Ensure appropriate pressure alarms are set. Consider re-

Alert

1 BELOW

calibrating the transducer, if alert cannot be explained by

MINIMUM

conventional troubleshooting.

Check for and resolve a physiological or mechanical cause.

PRESSURE

Ensure appropriate pressure alarms are set. Consider re-

Alert

2 BELOW

calibrating the transducer, if alert cannot be explained by

MINIMUM

conventional troubleshooting.

Check for and resolve a physiological or mechanical cause.

PRESSURE

Ensure appropriate pressure alarms are set. Consider re-

Alert

1 ABOVE

calibrating the transducer, if alert cannot be explained by

MAXIMUM

conventional troubleshooting. Consider reducing RPM to

reduce the pressure if appropriate.

Check for and resolve a physiological or mechanical cause.

PRESSURE

Ensure appropriate pressure alarms are set. Consider re-

Alert

2 ABOVE

calibrating the transducer, if alert cannot be explained by

MAXIMUM

conventional troubleshooting. Consider reducing RPM to

reduce the pressure if appropriate.

Switch to backup Console, Motor and Flow Probe accord-

MOTOR

Alert

ing to the procedure described in Section 2. Verify that the

OVER TEMP

backup Motor stands free and is not covered (e.g. blankets).

Press the alarm acknowledge button. If the alert message

BATTERY

repeats, switch to backup System as described in Section

Alert

CHARGER

2. If this alert is associated with BATTERY MODULE FAIL

FAIL

then carry out the procedure associated with that alarm.

BATTERY

Do not use the Console. Perform battery maintenance ac-

MAINTE-

Alert

cording to the Battery Maintenance Procedure listed in the

NANCE

CentriMag Circulatory Support System Operation Manual.

REQUIRED

Plug the Console into a AC power outlet to charge the

battery. If no AC outlet is available, switch to the backup

LOW

Alert

Console, Motor and Flow Probe according to the procedure

BATTERY

described in Section 2.

Resume support.

Verify that the user wants the Console to be on battery. If so,

ON BAT-

carefully monitor the status of the battery charge indicator,

Alert

TERY

while using the System on battery.

Reconnect to AC-outlet, as soon as possible.

PL-0370 Rev 00 / December 2019 / Page 1