diversey Taski swingo 350B Посібник - Сторінка 10

Переглянути онлайн або завантажити pdf Посібник для Прибиральне обладнання diversey Taski swingo 350B. diversey Taski swingo 350B 11 сторінок.

Друкувати сторінку

Service intervals

TASKI scrubber dryer machines are built to the highest quality standards, and

their safety is checked in the factory and by authorised inspectors. Electrical

and mechanical parts are subject to wear or aging if used for long periods of

time.

• In order to maintain operational reliability and

availability for use, the service must be carried

out after 250 working hours or at least once a

year.

Under rough or extreme working conditions and/or insufficient maintenance,

shorter periods are necessary.

Service centre

Should you contact us due to a malfunction or for placing an order, please

always state the type, description and the serial number of your machine.

You can find this information on the name plate of your machine, and the

address of your nearest TASKI partner can be found on the last page of this

manual.

Changing the squeegee blades

• Stand the machine on the parking support.

• Remove the squeegee by turning the locking

screws.

• Unscrew the triangular handle (1) and pull the

blade body (2) out of the squeegee body.

• You can now turn or replace the blade.

• Reinsert the blade body into the squeegee body and screw on the triangular

handle again.

Changing the wiper blade

• Stand the machine on the parking support.

• Press down the wiper by hand until the

snappers (1) for the cover plate appear.

• Press the snapper lugs (2) to the back until the

cover plate (3) can be removed.

• You can now turn or replace the blade.

• Now remount the cover plate (3). Ensure that

the snapper lugs (2) latch in correctly.

Caution:

Danger of injury from clamping the fingers!

Cleaning or replacing the float (indication for full recovery tank)

• Switch the machine off.

Disassembly:

• The yellow suction filter can be easily removed

(quick-fit seal).

• Clean it with water using a brush (let it dry out

well).

• Brush the yellow suction filter with a soft brush

or remove the fluff with a cloth.

Malfunctions

Malfunction

Possible causes

Battery disconnection

socket unplugged.

Machine does not

Batteries not charged,

run

or insufficiently

charged.

(When switching on:

red display on the

battery indicator)

The machine has

been overloaded,

Brush does not

causing the overcur-

turn

rent protection to be

tripped

Foam or liquid

leaking from the

Float malfunction

machine

The float closes the

inlet opening at the

suction unit (overfill

protection for

recovery tank)

Hose or nozzle

Poor vacuum

blocked e.g. by pieces

performance

of wood or residual

material

Floor remains

wet

The blades do not ad-

just well to the floor

Soiled solution

consistancy

not picked up

Worn blades

Dirt sieve full (yellow)

Solution tank empty

Output of clean-

Solution tank filter

ing solution insuf-

blocked

ficient

Water distributor

blocked

Troubleshooting

page

• Insert the disconnect-

ed charger jack

• Switch the machine on

• Check

• Fully charge the

battery

• Release the Drive

switch and then press

again.

• If necessary, switch on

the machine again.

• Turn off the suction

aggregate

• Check that the float is

functioning correctly

• A product has been

used that is unsuitable

for the scrubber dryer.

• Check the recovery

tank is not full

• Check the functionality

of the float

• Remove the blockage

• Clean the squeegee

• Change/turn the

blades

• Remove the dirt sieve

• Rinse the sieve

under running water

• Fill the solution tank

• Clean solution tank

filter

• Cleaning the water

distributor