3Doodler 2.0 Посібник - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник для Аксесуари 3Doodler 2.0. 3Doodler 2.0 4 сторінки.
Також для 3Doodler 2.0: Посібник із швидкого старту (2 сторінок), Посібник користувача (10 сторінок)

Друкувати сторінку

5. If you are still experiencing problems extruding or suspect there

may be a blockage in your 3Doodler, please remove the

Maintenance Cover

as follows:

Ensure the LED light is BLUE or GREEN before starting this

process (indicating that the pen is hot)

Using the included screwdriver or a pair of tweezers, pry up

the maintenance hatch from the back.

If you can see plastic wrapped around the drive gear (the

mechanism that moves the plastic forward), press either FAST

or SLOW extrusion button until the plastic ceases to be

wrapped around the drive gear and comes loose. If no plastic

is wrapped around the drive gears, go straight to step D below.

If there is any plastic in the pen, please use a pair of tweezer

to dislodge it so that it can be pulled out from the back of the

pen.

Tweezer

Plastic/filament

E) Align the maintenance cover, so that the hole is facing away

from the nozzle (as per the diagram). Push down on the

bottom of the maintenance cover till you hear it snap in.

For a full video of how to remove and replace your

Maintenance Cover please go to

the3Doodler.com/maintenance-cover

3Doodler 2.0

WARNINGS & NOTICES

ENGLISH

SPECIFICATIONS

Output Power: 6W

Output Voltage: 5V

Input Voltage: 5V

CARE & MAINTENANCE

For care and maintenance information, and more advice on how to

use your 3Doodler, please refer to our website: the3Doodler.com

To troubleshoot, please visit: the3Doodler.com/troubleshooting

LIMITED WARRANTY

For more details on your limited warranty, pleae visit:

the3Doodler.com/warranty

For 3Doodler's Terms and Conditions and other notices please

refer to our website: the3Doodler.com/terms-and-conditions

FCC NOTICE

CAN ICES-3 (B)/NMB-3(B)

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and

•

receiver.

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

•

for help.

Patent Pending

ADULT USE ONLY. THE 3DOODLER IS NOT A TOY FOR

CHILDREN. ALWAYS USE THE PROTECTIVE COVER

PROVIDED WITH YOUR 3DOODLER.

This marking indicates that this product should not be

disposed of with other household wastes. To prevent

possible harm to the environment or human health from

uncontrolled waste disposal, recycle it responsibly to

promote the sustainable reuse of material resources.

3Doodler, DoodleStand, JetPack, StrandStand, and

"#WhatWillYouCreate?" are trademarks owned by WobbleWorks,

Inc.

3Doodler 2.0

WARNINGS & NOTICES

Specifications are subject to change

and improvement without notice.

ENGLISH