Altox WBUS-4 v2 Посібник з експлуатації - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з експлуатації для Автомобільні аксесуари Altox WBUS-4 v2. Altox WBUS-4 v2 4 сторінки.

Друкувати сторінку

General Information

Dear buyers of ALTOX equipment!

We thank you for purchasing a new ALTOX WBUS-4 v2 device. This device

will provide you with great options to control your autonomous starting

parking heater.

You need a SIM card for your ALTOX device. It is recommended to use

special plans for M2M equipment.

Use

Using ALTOX system you can control your starting pre-heater remotely

using a phone. You can use all mobile and landline phones with tone dialing

option. Certain types of mobile phones (smart phones) can use apps and

the option of using web interface to control the system in the real-time

mode.

Control and Programming

You can start using your ALTOX module right after you have saved

authorized phone numbers in settings (3 cells: NUM1 / NUM2 / NUM3).

Saving of the ﬁrst caller's phone number into cell NUM1 follows up

automatically (cell NUM1 should be empty).

To save other phone numbers use a text message command NUMX:+YYYYY,

where X is a number from 1 to 3, and +YYYYY is a phone number.

To clear the cell send NUMX instruction without specifying a phone number.

There are the following control options:

- Outgoing voice call and DTMF commands;

- Outgoing text messages (SMS instructions);

- Mobile applications Thermo Call, HeaterRC or others;

- Direct control via a button in the car's interior;

- Via web interface of the mobile Internet app http://altox.ru/app

Control via an outgoing call

Call the phone number of the SIM card installed in the GSM module. The

phone number you are using to make a call should already be saved in the

device (see text messages SMS-commands). If the call is made using a

number that has not been saved in the ALTOX module, the connection with

the device will end without receiving a response signal. The working status

of the heater will not change.

When setting CALL1 is activated, ALTOX responds to the call and plays

voice prompts (option).

If this setting is not active (CALL0), the call is dropped after a certain

number of ringing tones. 1 ringing tone - the heater switches on,

2 ringing tones - the heater switches off.

SMS Status Messages:

HEATER ON 30min

- heater status and time until switching off

GSM (0-31): 28

- GSM receive signal level (not less than 10)

Voltage: 12.8V

- car-system voltage

Temp heater: 50С

- heater's temperature sensor's value

Flame: no

- heater's ﬂame sensor's value

Output: off

- auxiliary output OUT status

Note: if relevant data is not available, the ﬁelds will not be ﬁlled in

Text Messages with Error Codes:

Error code: none

- stored codes of the heater's errors

Note: in ТТС there are 3 error cells, FF response means there are no errors

Speciﬁcations

Parameter

Power Supply Voltage

Standby Current

Max Current for Auxiliary Output Terminals

Operating Temperature

Red

- Power Supply +12V (via fuse 1А)

Black - GND (Common)

Pink

- Input IN (connection of the button)

Blue

- WBUS

Grey - Auxiliary output OUT (commutates at +12V)

Please deactivate PIN code request

before inserting a SIM Card!

LED

LED status (in SIM card slot)

Solid - request to SIM card, searching for network connection

Slow blinking (once every 2 seconds) - waiting mode

Fast blinking (5 times every second) - establishing of GPRS/RING/SMS/USSD

Installing a Button to Switch on the Module

Make a Ø8mm hole in the plug or in another easily accessible for a driver

place. The button is connected in accordance with the color of the main

connector wires (key: Input IN - +12V, LED: output OUT - resistor - GND).

Note: if a non-latching button (FIXKEY1 setting) is used to switch heater on

heater will not be switched off automatically after time speciﬁed in TIME1.

Value

10V - 28V

less than 20mA

150mA

from -40 to +80°С