ClearWater DELUXE SYSTEM Посібник користувача - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник користувача для Диспенсер для води ClearWater DELUXE SYSTEM. ClearWater DELUXE SYSTEM 2 сторінки. High rate sand filter

Друкувати сторінку

CLEARWATER DELUXE SAND FILTER SYSTEM OWNER'S MANUAL

WARNING: A GFCI is required. Follow national and local building and

safety codes.

Your ClearWater Deluxe Sand Filter System is shipped complete, with all needed

components ready for assembly and installation.

System will require a 110 Volt / 20 Amp service. DO NOT use extension cords. Use

will void warranty on pump motor. The pool equipment should be located between

the pool skimmer and return line. The filtration system should not be installed less

than 2 ft. and no more than 5ft. from the pool. The ClearWater Deluxe Sand Filter

System needs to be on a completely flat level / surface (patio block, cement slab, etc.).

INSTALLATION INSTRUCTIONS

WARNING! READ ALL INSTRUCTIONS AND WARNING LABELS BEFORE

OPERATING FILTER!

1. Place filter with filter base on a level, secure surface. There is no need to

disassemble filter or pump assemblies. Position sand filter body securely onto filter

base. Align drain with drain clearance on base. Secure sand filter body to base

using bolt (#20) and washer (#21) as shown. DO NOT over tighten.

2. Open box and remove pump and trap.

3. Secure pump to pump base using pin and anchor assemblies (#24) (Detail 1).

4. IMPORTANT: To prevent damage to internal filter lateral components, fill filter

tank full with water prior to adding sand. With sand fill guide (#8) positioned in

filter tank opening, add only recommended #20 grade silica sand (see Fill Chart).

Remove sand fill guide. IMPORTANT: Clean and remove all debris from filter tank

flange after adding sand.

5. Assure that o-ring (#5) is positioned onto multi-port throat.

6. Install multi-port valve with inlet and outlet ports facing pool. Top of internal

stand pipe seats directly into multi-port valve. Push multi-port valve evenly onto

tank flange. NOTE: Make sure tank flange is clear of any sand debris.

7. Install filter tank split-nut assembly (#7, 7a & 7b) by threading split-nut clockwise

SYSTEM START UP

1. Fill pool until water is halfway up length of skimmer throat.

2. Make sure pump trap is full of water. Slightly loosen trap lid to relieve pressure and

allow water to fill trap. Re-tighten lid.

3. Make sure multi-port valve handle is in Filter position.

4. Plug pump into GFCI outlet and turn pump on. Turn two-speed pumps to high.

5. Make note of start-up pressure on gauge.

6. Check for leaks.

WINTERIZATION

1. Backwash filter system completely. See Cleaning Instructions.

2. Run a filter cleaning chemical through filter system as per cleaner instructions.

3. Turn pump off. Disconnect hoses from skimmer and return fitting.

4. Remove drain cap from bottom of filter tank (#18). DO NOT remove self-threading

drain assembly (#17).

5. Unscrew drain plugs located at bottom of pump trap and front of pump housing.

Let water drain completely.

6. Disconnect filter to pump connection. Loosen union connection on discharge of

pump and remove from pump. DO NOT lose 2" union gasket (#24). Lift and remove

pump and pump base from filter base. Store inside.

Assemble filter system only after above ground pool is installed. Fill pool with water.

IMPORTANT: Do no raise water level above pool return line or skimmer throat until

installation is complete.

NOTE: Open shipping carton in an upright position checking contents, as follows:

1. One-piece mounting base

5. One fittings bag

2. One pump

6. One collar wrench

3. One filter

7. Trap assemblies

4. Two corrugated hoses

8. Sand filter hose assembly

until hand tight. Then use split-nut wrench (#6) to tighten further (Detail 3).

8. To use split-nut wrench (#6), place on split-nut assembly, use both hands to turn

wrench 1/2 to 3/4 of a turn to secure multi-port valve to filter body (Detail 2).

9. Position and hand tighten smaller end of sand filter hose assembly (#15) to top

inlet port of multi-port valve (#4) by positioning gasket (#11) and hand tighten

onto already installed buttress (#10). Position and hand tighten other end of sand

filter hose assembly by positioning gasket (#25) and hand tighten onto volute on

pump (Detail 5). DO NOT over tighten.

10. Thread gate valve (#33) and 1 1/2" gasket (#11) onto suction side of pump trap and

hand tighten (Detail 4a).

11. Apply Teflon tape (4 wraps ideal) to Pressure Gauge (#3). Thread into multi-port

valve.

12. Remove 4 hose clamps (#14) and position over end of corrugated hoses (#13).

Install corrugated hose (#13) onto return sweep assembly (#12), on multi-port

valve and to pool return fitting. Tighten hose clamps. Install the other corrugated

hose between gate valve (#33) and pool skimmer fitting. Tighten hose clamps.

NOTE: Soften hose ends with warm water to ease installation onto fittings (if

necessary).

13. Install waste adapter fitting (#1) with o-ring (#2) (Detail 4).

CLEANING INSTRUCTIONS

NOTE: When pressure gauge reading is 5 PSI or higher than original starting pressure,

the filter needs to be cleaned. The ClearWater Deluxe Sand Filter System features

our exclusive 7-Position Multi-Port Valve, which ensures safe and simple filter

maintenance.

Pressurized vessel. Never attempt to loosen or open split-nut assembly (#7,

7a & 7b) while system is running. It could cause severe injury or harm to user.

NEVER CHANGE VALVE POSITION WITH PUMP RUNNING!

1. Turn off pump.

2. Attach backwash hose (optional) to waste port adapter.

3. Rotate multi-port valve handle to Backwash position. Turn pump on and run for

90 second intervals or until discharge water is clear. Turn pump off.

4. Rotate multi-port valve handle to Rinse position. Turn pump on for 30 seconds.

5. Repeat steps 3 & 4 until all discharge water is clear while pump is turned on.

6. Rotate multi-port valve handle to Filter position. Turn pump on. Valve is now in

normal operating position.

CLEARWATER DELUXE SAND FILTER SYSTEM PARTS LIST

Item

Part No.

Description

425-1928

Waste Adapter Fitting

805-0224

O-Ring

830-3000

Pressure Gauge

WVS003

Multi-Port Valve Assembly

805-0435

O-Ring

505-1970

Wrench - Split Nut

718-1960

Split-Nut - Sand Filter

819-0015

Screw - 1/4" - 20 PPH x 1 1/2"

820-0013

Hex Nut - Serrated 1/4"- 20

502-2011

Sand Fill Guide

505-1960

Threaded Sleeve for Split-Nut

417-4161

1 1/2" Buttress x 1 1/2" MPT

711-4000

1 1/2" Gasket

550-1841

Return Sweep Assembly

872-9002

Corrugated Hose - Black

872-0010

Hose Clamp - Stainless Steel

550-1811

16" Sand Filter Hose Assembly

550-1821

19" Sand FIlter Hose Assembly

550-1831

22" Sand Filter Hose Assembly

550-1833

26" Sand Filter Hose Assembly

515-1601

16" Sand Filter Body

515-1901

19" Sand Filter Body

515-2001

22" Sand Filter Body

515-2061

26" Sand Filter Body

16a

505-2040

16" Lateral and Manifold Assembly

505-2050

19" Lateral and Manifold Assembly

505-2060

22" Lateral and Manifold Assembly

505-2080

26" Lateral and Manifold Assembly

602-5310

Self-Threading Drain Screen

602-5301

Drain Cap

672-7211

Filter Base

819-0039

Bolt 3/8" - 22"

819-0016

Bolt 3/8" - 16" & 19"

820-0017

Washer 3/8" Flat

672-7201

Pump Base

PSP1100

1 HP - 1-Speed Supreme Pump

PSP1150

1 1/2 HP - 1-Speed Supreme Pump

PSP1200

2 HP - 1-Speed Supreme Pump

PSP2100

1 HP - 2-Speed Supreme Pump

PSP2150

1 1/2 HP - 2-Speed Supreme Pump

PSP2200

2 HP - 2-Speed Supreme Pump

429-7300

Pin & Anchor Assembly

711-4010

2" Gasket

311-1520

Faceplate - Supreme Pump

805-0330

O-Ring

319-1510

Supreme Pump Trap Body

319-1540

C-Clip Supreme Pump

319-1530

Supreme Trap Basket

805-0439

O-Ring

511-1310

Trap Lid

WV001H

Gate Valve

For Hard Plumbing: use 500-1901

1 ½" 90° Sweep Elbow

See instructions for proper

Union x Slip

valve alignment.

(optional/not included)

For Hard Plumbing: use 400-4060

1 ½" #7 Union Assembly

1 ½" S Pump End

(optional/not included)

16a

(not shown)

DETAIL 1

DETAIL 2

DETAIL 4

DETAIL 4a

Removal

Tool End

DETAIL 3

DETAIL 5