dji Ronin-MX Посібник із швидкого старту - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Аксесуари для фотоапаратів dji Ronin-MX. dji Ronin-MX 2 сторінки.
Друкувати сторінку
RONIN-MX
Quick Start Guide
Start
A. Download and install the DJI
Assistant app.
TM
Search "DJI Assistant" on the App Store and then follow the instructions for iOS
installation. Search "DJI Ronin
" on the Google Play and then follow the instructions for
TM
Android installation.
B. Before you start using your Ronin-MX, be sure to charge the DJI Intelligent Battery first.
Pressing the Intelligent Battery power button once will display the current battery level.
Press and hold for 1 second to turn on/off.
C. On the Remote Controller, slide the power switch to the right to power on. The battery level
indicators display the current battery status. If the low voltage alert sounds, recharge the
battery via the micro USB port.
Use a mobile device that runs iOS 7.1 or above or Android 4.3 or above.
●
Assembling the Ronin-MX
A. Deploy the tuning stand as shown. Tighten the knob.
B. Assembling the handle bar.
Press the buttons on the outside of the lower legs and
Attach the bars to both sides of the top handle and
rotate the legs downward, away from the stand. Then
tighten the grip screws.
Attach the grips to the bar and lock them in the preferred
press the buttons on the outside of the upper support
position.
arms and pull them upward, away from the stand.
Press the button on the vertical support and slide it up
Place the handle assembly on the tuning stand.
to extend the stand.
3
1
1
4
2
C. Attach the Ronin-MX to the handle.
D. To mount the DJI Intelligent Battery on the Ronin-MX,
Slide the gimbal horizontally into the handle bar.
loosen the thumb screws on either side of the battery
Tighten the knob when you hear a "click", which
and slide it directly into the gimbal. Tighten the thumb
indicates that the safety lock has engaged.
screws.
2
1
Mounting the Camera on the Mounting Plate
A. Attach the camera to the mounting plate and tighten the screws.
B. Attach the lens support to the mounting plate. Apply upward pressure to the lens support and tighten the screw.
C. Mount the Camera Upper Mounting Plate to the top of the camera through the hot shoe and then tighten the screws.
The steps above are suitable for most cameras. When mounting a RED or ARRI camera, the proper camera accessories
●
must be used.
Mounting the Camera on the Ronin-MX
A. Slide the mounting plate into the receiver until the safety lock engages.
B. Adjust the vertical position of the crossbar to meet the Camera Upper
Mounting Plate. When the camera achieves a rough balance, tighten
DJI Assistant
the camera base side clamp and the lock-knobs.
Low
Battery Level
High
Balancing
A. Balancing the Vertical Tilt
Rotate the Tilt Axis so that the camera lens is pointing
upward and loosen the two vertical adjustment tabs
and the lock-knobs on the top crossbar.
Gently slide the camera mount crossbar forwards or
backwards until the camera points upwards when
released. Latch the tabs back into their closed
position and tighten the lock-knobs.
2
C. Balancing Depth for the Tilt Axis
Open the side clamp and loosen the lock-knob
on the crossbar to slide the camera forwards or
backwards until the Tilt Axis remains level and
then tighten the side clamp and lock-knob.
1
2
Pairing with the DJI Assistant App
A. Power on the Ronin-MX. Switch on your mobile device's Bluetooth and
launch the DJI Assistant app.
B. Connect your mobile device to the Ronin-MX within the DJI Assistant app.
C. Check balance on the Viewer page. If a particular motor axis indicates a
power greater than 10, rebalance the camera.
Activation is required when using the Ronin-MX for the first time, otherwise
●
the gimbal will not work. To activate your Ronin-MX, connect your mobile
device to the Internet, then enter the "More" page in the DJI Assistant app
and tap the "Activate" button.
B. Balancing the Roll Axis
Loosen the three lock-knobs to slide the camera left or
right until the Roll Axis remains level, and then tighten the
three lock-knobs.
1
2
3
2
1
D. Balancing the Pan Axis
Open the clamp on the Pan Axis and turn the knob to
slide the assembly. Tighten the clamp after balancing is
completed.
1
2
1
3
2
Viewer
Power
2
Pan Axis
-2
Tilt Axis
Roll Axis
0
Power
Voltage
14.50V
Temperature
35.40
0:01:59
Time
Gimbal
Control
Using the Ronin-MX on the Ground
A. DJI Assistant App Tuning
With the Ronin-MX on the tuning stand and a properly balanced camera, tap Camera Type
1
and select DSLR Camera or RED Camera.
Switch on/off Briefcase Mode and SmoothTrack, and adjust the control speed as needed.
2
You can also use the DJI Assistant software for PC/MAC to activate and configure the
●
Ronin-MX. For more information, refer to the User Manual.
B. Connecting the Remote Controller to the Ronin-MX
Turn on the Ronin-MX. Press the recessed Bind Button of the Ronin-MX once with a
1
pointed object.
Turn on the Remote Controller. If the LED on the gimbal turns solid green, the Remote
2
Controller and the Ronin-MX have been successfully bound.
C. Remote Controller Operation
FUNCTION Switch:
1
i. Select the SmoothTrack speed according to the
following positions:
Position 1
Position 2
Position 3
-Fast
-Normal
ii. Quickly flipping the FUNCTION switch up and
down 3 times will enable/disable Motor Kill.
Left Stick: Horizontal movements on the left stick
3
control the roll axis.
Right Stick: Horizontal movements on the right
4
stick control the pan axis. Vertical movements on
3
the right stick control the tilt axis.
Using with the Matrice 600
Ensure the Ronin-MX has been activated, the camera is mounted securely and the balance is adjusted properly. Ensure the
upper cover and lower cover of the Matrice 600's center frame and the expansion mounting kit have been removed.
A. Mounting the Ronin-MX onto the Matrice 600
Connect one end of the provided CAN cable to the CAN1 port on the Matrice 600's main controller, and pull the other
1
end through the outlet of the center frame. Then re-mount the Matrice 600's upper and lower covers.
Adjust the Ronin-MX vibration absorbtion mounting plate, then tighten the screws on the connector.
2
Mount the vibration absorber onto the bottom of the Matrice 600 with the lock-knob facing forward, then tighten the 12
3
vibration absorber mounting screws provided.
3
Slide the gimbal into the gimbal connector of the vibration absorber, then tighten the lock-knob when you hear a "click".
4
Connect the CAN cable to the CAN2 port on the Ronin-MX.
5
？
Angle
1.89
。
-0.45
。
。
-0.01
Angle
Be sure the Ronin-MX is mounted properly and firmly, and all the connections are correct and will not obstruct the
●
Ronin-MX's movements.
B. DJI GO App Tuning
Set the App Output Mode in the DJI GO app: Tap
1
Allocation to ensure that the "HDMI" percentage is more than 0%. Set the App Out Mode to HDMI.
。
Tap
>
> Camera Type to configure the gimbal.
2
C. Use the Matrice 600's Remote Controller to control the Ronin-MX.
Viewer
More
Mode：
N/A
Gimbal
Wizard
？
Configuration
Stiffness Strength Outfilter Control
Pan Axis
55
40
0
20
Tilt Axis
45
40
0
60
Roll Axis
45
40
0
60
Camera Type
DSLR Camera
Live Data
Power
Angle
Pan
0
0
Tilt
0
0
Roll
0
0
Gimbal
Control
Viewer
More
Bind Button
MODE Switch: For toggling SmoothTrack.
2
Position 1
-Free, SmoothTrack Off
-Slow
Position 2
-Free, SmoothTrack On
-Reset to Center, SmoothTrack On
Position 3
, disable the EXT Port, and then adjust the Bandwidth