djpower TOPCAT HF-90 Посібник користувача - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник користувача для Ді-джейське обладнання djpower TOPCAT HF-90. djpower TOPCAT HF-90 13 сторінок. Flame machine
Друкувати сторінку•
After the machine is turned on, it is strictly forbidden to stay in the dangerous area of the machine. Safety distances for HF-90： At least
5m in all projection directions.
•
Please prepare dry powder and fire extinguishing equipment at the machine use place. Always have a dry powder fire extinguisher, CO2
fire extinguisher, and an extinguishing blanket in case of needed.
1.5.2.
Mounting and Rigging
•
CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid ballroom) condensation
may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•
Do not mount the product on a flammable surface (linoleum, carpet, wood, paper, carton, plastic, etc.). Keep a safe distance from the
unit, the unit can only be placed horizontally.
1.5.3.
Power and Wiring
•
Please use a grounded socket to avoid the risk of electric shock.
•
Make sure power supply in consistent with the rated voltage of the equipment, Unplug and turn off the machine when not use.
•
Check that the power cord is not pinched or damaged.
•
Do not connect the machine to a dimming controller or varistor.
•
Do not disconnect the power supply by pulling the power cord.
1.5.4.
Operation
•
The maximum ambient temperature is 40 ° C. Do not operate the machine in a high temperature environment.
•
Do not operate this product if the machine casing or cable is damaged. Immediately ask the authorized technician to replace the
damaged part.
•
Make sure there are no flammable materials around the machine before operation, and keep a safe distance between the person and
the equipment. The Safe distance for the HF-90 is: at least 5m in all projection directions.
•
Before connect the power cable, communication DMX cable should well connected and ensure the command keep at firing OFF status.
And safety lock stay at test mode
•
The operator responsible for the control of Wave flame machine must always have a clear view of the device, so that he/she can stop
the show immediately when there is danger. The main AC power switch should near operator. So that operator can turn off the power
of all devices in case of abnormal.
•
If there be any doubt as to the safety operation of the device in any circumstances, the device should be taken out of service immediately.
Be sure the device is in good operating condition before use, check the sparkle oil, fuse, cable and power plug. If fail to fire correctly,
immediately shut down and contact the factory.
•
Empty the Flame Fluid Can before transporting the machine.
•
The machine does not contain any user disassembled and self-repaired or modified parts. Do not attempt to repair or modify the machine
yourself without any training or authorized technicians to avoid damage or malfunction.
•
Notes for use of Battery power supply: HF-90 with stable internal circuit design, please support the unit with battery voltage higher than
12V. The driving speed of motor won't change because of the decrease of battery power supply. Battery options: 12V lead-acid battery
(above 30AH, with more than 24h standby). For Lithium battery, please use battery with output above 30A. 4 pin sound coupliers (1+
connect 12V anode, 1- connect 12V cathode). Connecting power cables should be above 14AWG.
•
Be sure to use the suitable flame fuel indicated in the user manual, otherwise, it is easily lead to failure or danger. Do not add any material
other than the specified proportion of castor oil in the oil drum. Be careful when refill the flame fluid tank. Please keep flame fluid away
from heat source, sparks, fire or other possibility of ignition.
Please save this manual for future use. Sell the machine again, be sure to attach the instructions.
- 2 -