CustomWorks INTIMIDATOR GSX2 Посібник - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник для Іграшкова машинка на колесах CustomWorks INTIMIDATOR GSX2. CustomWorks INTIMIDATOR GSX2 17 сторінок. Racing kit
Clutch Bag
Clutch Bag
Clutch Bag
Clutch Bag
Clutch Bag
-Parts for
Clutch
Bag
4430
Qty 1
4437
Flywheel
Collet
- Slide the 4437 Collet onto you motor followed by the 4430 Flywheel.
- Secure the Flywheel using 4442 SG Nut.
- Place the 4435 Clutch Shoes onto the clutch facing the direction shown and
secure with 4431 Clutch Springs.
NOTE: Install the springs by placing one leg on the Shoe, then press the other
leg into the groove in the Clutch Nut using a Driver Wrench.
- Slide 4438 Bearing onto the motor shaft followed by the 4440 Clutch Bell then
the 4439 Flanged Bearing.
- Secure the assembly using 5208 Screw. The clutch bell should spin "FREELY"
with the screw tight. It is OK if the clutch bell slides back and forth on the
motor shaft slightly. If there is too much play use the extra shims provided
to correct this.
- Thread the 4523 Pinion Gear onto the Clutch Bell with the side of the pinion
with the threads all the way to the edge facing AWAY from the motor.
4523
4438
5208
Body Mounts
Body Mounts
Body Mounts
Body Mounts
Body Mounts
-Parts for
3012
Qty1
INT Front Bumper
Body
Mounts
3228
Long Body Post
FRONT
3229
POST
- Slide the Post Collar onto the 3229 Short Body
5207
Post, use the Set Screw to retain the Collar
3012
- Mount the (2) 3229 Short Body Posts to the for-
ward set of holes on the 3012 Bumper.
5217
- Attach the 3012 Bumper to the 1287 Front Clip
using 5283 Screws and 5207 Nuts.
- Mount the 1287 Front Clip to the Chassis in the
second set of holes from the front edge of the
chassis using 5253 Screws and 5217 Nuts.
1287
5283
5283
Clutch Assembly
Clutch Assembly
Clutch Assembly
Clutch Assembly
Clutch Assembly
Qty 1
4435 Qty 2
4442 Qty 1
Clutch Shoe
SG Nut
4440
4431
4439
Body Mounts
Body Mounts
Body Mounts
Body Mounts
Body Mounts
1287
Qty1
INT Front Clip
Qty2
3229
Short Body Post
5253
REAR
- Mount the (2) 3228 Long Body Posts to the
1004 Rear Body Mount.
- Attach the 1004 to the Trans Brace using
5253 Screws and 5217 Lock Nuts.
4431
Qty 2
4440
Clutch Spring
Clutch Bell
4430
4435
4442
1004
Qty 1
5283
Rear Body Mount
8-32 x 1/2 FH Screw
Qty2
3229 Qty2
Post Collar
4438
Qty 1
4523
Qty 1
Flanged Bearing
23T Pinion
4437
1:1
Qty 4
5207
8-32 Lock Nut
1:1
5253
Qty 4
4-40 x 3/8 BH Screw
3229
COLLAR
SET SCREW
Qty 1
4439
Qty 1
5208
Qty 1
Clutch Bearing
M3x6mm SH
3229
Qty 2
Qty 4
Set Screw
5217
Qty 2
4-40 Lock Nut
3228
POST
5253
1004
5283