CustomWorks NITRO ROCKET KIT 0715 Посібник - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник для Іграшкова машинка на колесах CustomWorks NITRO ROCKET KIT 0715. CustomWorks NITRO ROCKET KIT 0715 16 сторінок.

Друкувати сторінку

Bag E

Diff Assembly

-Parts for

Step#1

4403

Qty 1

Right Outdrive

-Parts for

Step#2

4402

Qty 1

Left Outdrive

STEP #1

4361

CUSTOM-TIP!!!

-Using 400 Grit Sandpaper in a"Figure 8"

4361

pattern, it is best to sand the surfaces

of both the 4404 Diff Ring and 4205

4204

Thrust Washers. The textured

4205

4403

1229

- Slide a 4205 Thrust Washer onto the Diff Bolt.

- Apply a thick layer of Black Grease to the Thrust

Washer, press (6) 4204 Thrust Balls into the Black

Grease.

- Slide the other Thrust Washer on the Diff Bolt and

insert it into the 4403 Left Outdrive.

- Press (1) 1229 Bearing into the Outdrive.

- Put (1) 4404 Diff Ring on the Outdrive, apply Diff Lube

as shown.

Bag F

Transmission Casing

-Parts for

Step#1

LEFT

4401

Transmission Halfs

-Parts for

Step#2

1230

3/8 x 5/8 Bearing

- Press the (2) 1230 Bearings

and (4) 1226 Bearings into

each 4401 Transmission Half.

- Slide (1) 4370 Thick Washer

on each side of the 4368 Top

Drive Shaft.

- Insert the Diff Assembly,

Top Drive Shaft, and 4405 Idler

Gear into the RIGHT Trans

Half.

- Align the LEFT Trans Half over

the gears and secure it to the

RIGHT Trans Half with (5) 5273

Screws.

4404

Qty 2

4205

Diff Ring

Thrust Washer

4362

Qty 1

Diff Spring

surface results in a smoother and

longer lasting diff.

4404

DIFF

LUBE

RIGHT

Qty 1

Qty 2

4368

Top Drive Shaft

STEP #1

5273

Qty 2

4361

Qty 1

Diff Bolt Cover

4407

Qty 1

Diff Gear

4403

- Press a small amount of Diff Grease

into each of the small holes in the

4407 Diff Gear.

- Press (1) 1229 Bearing and the (12)

4357 Diff Balls into the Diff Gear.

- Put (1) 4404 Diff Ring onto the 4403 Right Outdrive, apply

Diff Grease as shown.

- Install the 4362 Diff Spring and 4361 T-nut into the

Outdrive.

- Carefully slide the diff assembly together so the Diff Bolt

passes thru the entire assembly and threads into the T-nut.

-Screw the Diff Bolt into the T-nut until you feel the Diff

Spring fully compress. DO NOT OVERTIGHTEN!!!

- Back the Diff Bolt off EXACTLY 1/8 of a turn. Diff motion

should be smooth and the Outdrives will turn in opposite

directions.

4405

Qty1

Idler Gear

Qty 1

4370

1226

4368

4405

1230

- Diff Screw should be on the

4401

RIGHT side of the Trans!

LEFT

1:1

4204 Qty 6

4361

Qty 1

Thrust Balls

Diff Bolt

4357

Qty 12

Diff Balls

STEP #2

1229

4357

4407

1:1

4370

Qty 6

1226

Thick Spacer

3/16 x 3/8 Bearing

1:1

5273

Qty 5

4406

4-40 x 3/8 SH Screw

Top Shaft Roll Pin

4370

1226

1230

4401

RIGHT

1:1

1229

Qty 2

5/32 x 5/16 Bearing

4361

Qty 1

Diff T- Nut

4404

4402

4362

4361

1:1

Qty 4

Qty 1

STEP #2

4406

- Press the 4406 Roll

Pin into the hole in

the Top Drive Shaft.