DKS 8040 microplus Посібник користувача - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник користувача для Приймач DKS 8040 microplus. DKS 8040 microplus 4 сторінки. Rf receiver (weigand)
Також для DKS 8040 microplus: Посібник користувача (3 сторінок)

Друкувати сторінку

1. Learn Transmitters

1. Turn the Programming Selector to Position 1.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Receiver is now in "Learn Mode" and will

flash and beep every second for 10 seconds.

3. Press a specific button on the desired transmitter to be "Learned" within 10 seconds. Receiver will reset 10 second timer after each transmitter

button has been pressed.

2 and 3 Button Transmitters Note:

There are three (3) different "2-Button" transmitter button combinations that each receiver can be programmed to respond to: button-1,

button-2 and buttons 1&2 pressed at the same time.

There are six (6) different "3-Button" transmitter button combinations that each receiver can be programmed to respond to: button-1, button-2,

button-3, buttons 1&2 pressed at the same time, buttons 2&3 pressed at the same time and buttons 1&3 pressed at the same time.

Press and

2 Sec.

Hold Program

Button

One Quick Flash

START

and Beep

4. Press other desired transmitter buttons to be learned, each within a 10 second time period.

Less than 10 Seconds Idle Time

1 Sec.

Activate another

desired Transmitter

Beep

5. After all desired transmitters have been learned by the receiver, wait for the receiver to time-out.

2. 26-Bit Weigand (Factory Set)

1. Turn the Programming Selector to Position 2.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once.

3. Receiver LED will then give a long flash and beep.

4. This indicates receiver is now in "26-Bit Weigand Mode".

START

3. 31-Bit Weigand

1. Turn the Programming Selector to Position 3.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once.

3. Receiver LED will then give a long flash and beep.

4. This indicates receiver is now in "31-Bit Weigand Mode".

START

4. 30-Bit Weigand

1. Turn the Programming Selector to Position 4.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once.

3. Receiver LED will then give a long flash and beep.

4. This indicates receiver is now in "30-Bit Weigand Mode".

START

5. Match Facility Code

1. Turn the Programming Selector to Position 5.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once.

3. Receiver LED will then give a long flash and beep.

4. This indicates receiver will check the facility code for a match before outputting the transmitter code.

START

Less than 10 Seconds Idle Time

1 Sec.

Release

Button

Beep

Less than 10 Seconds Idle Time

1 Sec.

Beep

Transmitter Programming Mode

Press and

2 Sec.

Hold Program

Button

Quick Flash

and Beep

Press and

2 Sec.

Hold Program

Button

Quick Flash

and Beep

Press and

2 Sec.

Hold Program

Button

Quick Flash

and Beep

Press and

2 Sec.

Hold Program

Button

Quick Flash

and Beep

1 Sec.

Beep

Transmitter Programming Mode

Activate another

desired Transmitter

Release

Button

Long Flash

and Beep

Release

Button

Long Flash

and Beep

Release

Button

Long Flash

and Beep

Release

Button

Long Flash

and Beep

1 Sec.

Activate ONE MicroPLUS

or MicroCLIK™ Transmitter

1 Sec.

After 10 Seconds

Timer Times-Out

Beep

Indicates 26-Bit Weigand Mode

FINISH

Indicates 31-Bit Weigand Mode

FINISH

Indicates 30-Bit Weigand Mode

FINISH

Indicates receiver will check facility code for a MATCH

FINISH

Timer is Reset

to 10 Sec.

FINISH