ALUZ ZIBI A1 Series Посібник
Переглянути онлайн або завантажити pdf Посібник для Освітлювальне обладнання ALUZ ZIBI A1 Series. ALUZ ZIBI A1 Series 11 сторінок. Surface zuco pivot bios illuminated
Також для ALUZ ZIBI A1 Series: Інструкція з монтажу Посібник з монтажу (12 сторінок), Посібник (13 сторінок), Посібник (11 сторінок), Інструкція з монтажу Посібник з монтажу (11 сторінок)
Друкувати сторінкуGENERAL FEATURES
Applications
Wall Washing Lighting
Lens
Tempered Clear Glass Lens
Optics &
10° - 60° or Asymmetric Optics
Asymmetric
Length
Built to Order (2', 3', or 4' Increments)
Construction
Aluminum Extrusion
Weight
5.6 lbs (2'), 7.9 lbs (3'), 11.2 lbs (4')
Mounting
Mounting Clips (Sold Separately)
Dry or Wet (IP65 or IP67) Location
UL1598, CSA C22.2#250.0
Listing
UL8750, CSA250
UL2108, CSA C22.2 #9
Driver
Integral
Temperature
Operating / Startup: -20° to 48°C (-4° to 120°F)
Ratings
Storage: -40° to 76°C (-40° to 170°F)
Installation Link
ELECTRICAL
Dimming
DMX
Maximum Run
100' (3W), 64' (5W), 53' (6W),
(Line Voltage
40' (8W), 35' (9W), 26' (12W), 21' (15W)
Integral Driver)
Luminaire Voltage
120V - 277V (UNV)
1170 N Red Gum St, Anaheim, CA 92806
aluz.lighting
© ALUZ All Rights Reserved. ALUZ reserves the right to make changes or withdraw specifi cations without prior notice.
A1 Series | Surface
ZIBI Pivot RGBW
(A1-ZIBI-PVT-RGBW)
866.ALUZ.LTG | 714.535.7900
READ ENTIRE GUIDE BEFORE STARTING INSTALLATION
Important Notice: Verify correct luminaire was received with correct
color temperature, voltage, and wattage before cutting or installing.
ALUZ will not be responsible if incorrect luminaire is installed.
END VIEWS / DIMENSIONS
2.53"
2.62"
0° Tilt (Minimum)
PRODUCT INFORMATION
• Lighting for wall washing, cove, edge, undercabinet, accent, displays
• Line Voltage (Integral Driver) or Low Voltage (Remote Driver)
• Color changing LEDs
• Available in 3 Watts up to 18 Watts Per Foot
• Product is shipped in 1', 2', 3', and 4' luminaires
• Available for outdoor rated installations
ELECTRICAL REQUIREMENTS
• Line Voltage luminaires do not require a remote driver.
• Maximum load per line voltage fi xture is 320 watts per circuit.
INSTALLATION TOOLS REQUIRED
• Electric Hammer Drill
• 14.4 to 28 Volt Cordless Drill
• Phillips Bits
• Utility Knife
• Electrical Cord
• Marker
• Wire Stripper
DMX WIRING DIAGRAM (Dry or Wet Location)
DMX WIRING NOTES
• Default DMX address per RGBW luminaire.
DMX Address 001 = Red
DMX Address 002 = Green
DMX Address 003 = Blue
DMX Address 004 = White
• Consult third party DMX commissioner to modify at time of installation.
• Connection from DMX controller to luminaire must be made using a proper daisy
chain connection per DMX-512 / RDM standards.
• Do not make DMX wiring connections in parallel.
• When connecting DMX Shield to a DMX controller terminal, ensure that it is not
connected to or touching earth ground, chassis ground, and/or DC power (-) return.
Page 1 of 11
Overview
3.53"
3.85"
90° Tilt (Maximum)
• Long Nose Pliers
• Drill Bits - Concrete or Wood
• Electrical Three Ways
• Safety Glasses
• Measuring Tape
• Laser Line or Chalk Line
DMX+ (White)
DMX- (Blue)
DMX Shield (Sleeve)
Ground (Green / Yellow)
Neutral (Blue)
Hot (Brown)
Primary Voltage
120-277V AC
Installation Instructions
4 / 29 / 2022 / Rev 2
DMX
Signal