AKO AKO-14545-C Короткий посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Короткий посібник для Контролер AKO AKO-14545-C. AKO AKO-14545-C 2 сторінки.
Також для AKO AKO-14545-C: Посібник (2 сторінок)

Друкувати сторінку

8- Table of parameters and messages

The Def. column indicates the ex-works configured default parameters. The pressure values featured on the table are expressed in bar and those for temperature in ºC. If the wizard meanwhile selects

another set of units (parameter C09), the equipment will make the conversion automatically.

INSTALLATION CONFIGURATION

Description

C01

Total number of compressors (with or without inverter)

CnF

C02

Number of stages per compressor

Polarity of the capacity reduction contact

C03

0=Active when closing the contact; 1=Active when opening the contact

C04

Compressor 1 with frequency inverter 0=No; 1=Yes

C05

Total number of fans (1 inverter only is considered with inverter)

C06

Fan control type 0=ON/OFF; 1=Frequency inverter

C07

Operation type 0=Direct; 1=Inverse

Refrigerant gas type

0=R134a 1=R404a 2=R717a 3=R22

C08

6=R744 7=R407a 8=R407f 9=R1234y 10=R448a 11=R449a 12=R450a

Display units (Primary-Secondary) 0=bar-ºC 1=psi-ºF

C09

3=bar-ºF 4=ºC-bar 5=ºF-psi

6=ºC-psi 7=ºF-bar

C10

Frequency inverter output type 0=4-20 mA; 1=0-10 V

InI

This indicates the configuration selected in the wizard (read only)

Output to level 1

EVAPORATION CONFIGURATION

Description

E01

Pressure / evaporation temperature set point

EPr

E02

Evaporation set point upper limit (It cannot be set above this limit)

E03

Evaporation set point lower limit (It cannot be set below this limit)

Compressor rotation type: 0=Balancing, depending on the operation time

E04

1=Sequential (the last in is the first out)

E05

Compressor control type: 0=Neutral zone; 1=Proportional

E06

Evaporation regulation bandwidth

E07

Integral time (PID inverter control)

E08

Stop value for pump down (If C07=0)

E09

Maximum pump down time (If C07=0) (0= deactivated)

Output to level 1

CONDENSATION CONFIGURATION

Description

F01

Condensation pressure / temperature set point

Cnd

F02

Condensation set point upper limit (It cannot be set above this limit)

F03

Condensation set point lower limit (It cannot be set below this limit)

Fan rotation type: 0=Balancing, depending on the operation time

F04

1=Sequential (the last in is the first out)

F05

Fan control type: 0=Neutral zone; 1=Proportional

F06

Condensation regulation bandwidth

F07

For fans when the compressors stop 0=No; 1=Yes

F08

Floating condensation 0=No; 1=Yes

F09

Integral time (PID inverter control)

F10

Floating condensation minimum set point value ( see remark 1)

F11

Condenser temperature delta

Output to level 1

PROBE CONFIGURATION

Description

P01

Probe type selection 0=4-20 mA; 1=0-5 V; 2=NTC

Probe to be displayed: 0=Probe 1 (Aspiration)

CnP

P02

2=Probes 1 and 2 in carousel

P03

Value 4 mA / 0 V (according to P01) probe 1

P04

Value 20 mA / 5 V (according to P01) probe 1

P05

Probe 1 calibration (Offset)

P06

Value 4 mA / 0 V (according to P01) probe 2

P07

Value 20 mA / 5 V (according to P01) probe 2

P08

Probe 2 calibration (Offset)

P09

Calibration of the outside temperature probe for floating condensation

Output to level 1

DIGITAL INPUT CONFIGURATION

Description

Polarity digital input 1 (thermal stage 1): 0=Activates on closing contact;

I01

Cni

Polarity digital input 2 (thermal stage 2): 0=Activates on closing contact;

I02

Polarity digital input 3 (thermal stage 3): 0=Activates on closing contact;

I03

Polarity digital input 4 (thermal stage 4): 0=Activates on closing contact;

I04

I05

Polarity digital input 5: 0=Activates on closing contact;

I06

Polarity digital input 6: 0=Activates on closing contact;

Digital input 5 function:

0=Low pressure alarm

I07

2=Thermal stage alarm 5 3=Ambient temperature probe 4=External alarm

5=Remote disconnection ON-OFF 6=Variation in the aspiration set point (E01) (see remark 2)

Digital input 6 function:

0=Low pressure alarm

I08

2=Thermal stage alarm 5 3=Ambient temperature probe 4=External alarm

5=Remote disconnection ON-OFF 6=Variation in the aspiration set point (E01) (see remark 2)

I09

Turn-on delay time of digital input 5 (not applicable if I07=2)

I10

Turn-on delay time of digital input 6 (not applicable if I08=2)

I11

Variation in the evaporation set point (new set point= E01+I11) (see remark 2)

I12

Duration of the variation in the evaporation set point (see remark 2)

Output to level 1

ENERGY SAVING CONFIGURATION

Description

Start of energy saving - Day of the week: 0=Deactivated 1=Monday 2=Tuesday

S01

3=Wednesday 4=Thursday 5=Friday 6=Saturday

9=Monday to Saturday

10=Monday to Friday

S02

Start of the energy saving - Hour (see remark 2)

S03

Start of the energy saving - Minute (see remark 2)

S04

Duration of the energy saving (see remark 2)

Variation in the evaporation set point during energy saving

S05

(E01+S05) (see remark 2)

Output to level 1

Read only parameters can only

be edited using the INI wizard.

Units

4=R410a 5=R507a

2=psi-ºC

Units

bar

sec.

bar

sec. x 10

Units

bar

sec.

ºC

Units

1=Probe 2 (Discharge);

bar

ºC

Units

1=Activates on opening contact

1=High pressure alarm

sec.

bar

min.

Units

7=Sunday 8=Monday to Sunday

11=Saturday to Sunday

min.

bar

Min. Def. Max.

Description

t01

Minimum operation time for a compressor

Tep

t02

Minimum disconnection time for a compressor

t03

Delay time between the compressor start-up/stage and the next one

t04

Delay time between the compressor stop/stage and the next one

t05

Minimum operation time for a fan

t06

Minimum disconnection time for a fan

t07

Delay time between the fan start-up and the next one

t08

Delay time between the fan stop and the next one

Output to level 1

Description

A01

Number of active compressor stages with error in probe 1

A02

Number of active fans or inverter % with error in probe 2

A03

Low pressure alarm in probe 1

A04

Low pressure alarm differential

Min. Def. Max.

A05

High pressure alarm in probe 2

E03

E02

A06

High pressure alarm differential

E03

A07

Alarm delay after reaching the value

-0.7

E02

A08

Delay of temperature alarms in the start-up.

High pressure alarm limit (per digital input) per hour without manual reset. (If I07 or

A09

I08=1) (0=deactivated) Once the limit has been exceeded a manual reset will be required

for each new alarm.

0.0

2.0

Output to level 1

-0.7

0.1

Description

255

r01

Hour

rtC

r02

Minutes

r03

Day

Min. Def. Max.

r04

Month

F03

F02

r05

Year

F03

Output to level 1

-0.7

F02

Description

Address for units with communication

tid

Access code (Password)

0.0

2.0

Programme version

Check

Output to level 1

-50

99.9

Description

This shows the operation time for the compressor or fan 1

tFC

This shows the operation time for the compressor or fan 2

This shows the operation time for the compressor or fan 3

Min. Def. Max.

This shows the operation time for the compressor or fan 4

This shows the operation time for the compressor or fan 5

Output to level 1

Programming output

-60

999

-60

999

* Dependin

g on the compressor control type: Proportional=E01; Neutral zone=E01-E06.

-20

** If the compressor is equipped with an inverter, this period of time halves.

-60

999

*** The number of st

-60

999

Remark 1: The equivalent value in pressure is calculated depending on the refrigerant gas

-20

specified in the wizard.

-20

Remark 2: In the event of the energy saving and the variation in the set point per digital input

being activated at the same time, the variation in the set point per digital input will

always prevail.

Min. Def. Max.

MESSAGES

Access code (Password) request

PdA

Pump down detained due to time

Clock battery dead or clock deprogrammed

ALL

Low pressure alarm due to probe 1

ALH

High pressure alarm due to probe 2

At1

Thermal alarm 1

AT2

Thermal alarm 2

At3

Thermal alarm 3

At4

Thermal alarm 4

At5

Thermal alarm 5

AES

Severe external alarm (input I5 or I6)

0FF

Remote regulation detained due to digital input (input I5 or I6)

LPA

Low pressure alarm due to digital input (input I5 or I6)

High pressure alarm due to digital input (input I5 or I6)

HPA

255

Error in probe 1 (open circuit, probe crossed or out of range)

255

Error in probe 2 (open circuit, probe crossed or out of range)

-20

Error in probe 3 (open circuit, probe crossed or out of range)

255

D: The message is shown on the display.

Min. Def. Max.

R: Alarm relay activated (if available, see WIZARD table).

-20

TIMING CONFIGURATION

CONFIGURATION OF PROTECTIONS AND ALARMS

DATE AND TIME CONFIGURATION

ACCESS AND INFORMATION CONTROL

OPERATION TIMES

ages depends on the configuration selected in the wizard.

Units

Min. Def. Max.

sec. x10

999

sec. x10

999

sec.

999

sec.

999

sec. x10

999

sec.

999

sec.

999

Units

Min. Def. Max.

Without inverter

C05

With inverter

100% 100%

bar

-0.7

bar

0.1

1.0

bar

-0.7

bar

0.1

1.0

999

sec.

255

Units

Min. Def. Max.

Units

Min. Def. Max.

255

999

Units

Min. Def. Max.

hours x10

999

hours x10

999

hours x10

999

hours x10

999

hours x10

999

D -

D R

D -

D R