AKO PROCool AKO-17635-1 Короткий посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Короткий посібник для Панель керування AKO PROCool AKO-17635-1. AKO PROCool AKO-17635-1 4 сторінки.

Друкувати сторінку

Advanced configuration

The parameters are grouped into 6 sections depending on their function.

Temperature values are expressed in ºC. (Equivalent temperature in ºF)

If the access code is activated, a 2 digit code is requested, if the code entered is incorrect the unit will not enter programming mode.

After 20 seconds with no key being pressed, the equipment will return to the previous level. If you are on level 3, the changes will not be saved.

REGULATION AND CONTROL

Description

Temperature Adjustment (Set Point)

Calibrating probe 1 (Offset)

Probe 1 differential (Histeresis)

Upper blocking of the set point

(cannot be set above this value)

Lower blocking of the set point

(cannot be set below this value)

Type of delay for protection of the compressor

0=OFF/ON (since the last disconnection);

1=OFF-ON/ON-OFF (since the last shut-down /start-up)

Protection delay time

(value of the option selected in parameter C4)

Status of COOL relay with probe fault

0=OFF; 1=ON; 2=Average based on last 24 hours prior to probe fault;

3=ON-OFF as prog. C7 and C8

Time relay ON in case of faulty probe

(If C7=0 and C8¹0, the relay will always be OFF deenergised)

Time relay OFF in case of fault of probe 1

(If C8=0 y C7¹0, the relay will always be ON energised)

Idle time of the digital input for the change Set Point function to be

C11

activated (Only if P10 or P11 =1) (0=OFF)

Variation of the set point (SP) when the change set point function

C12

is active. (SP+C12 £ C2) (0= disabled)

Exit to Level 1

DEFROST CONTROL

Description

Defrost frequency (Time between two starts)

dEF

Maximum defrost duration (0=defrost deactivated)

Type of message during defrost:

0=Current temperature; 1=Temperature at start of defrost;

2=Display dEF message

Maximum duration of message

(Time added at the end of the defrost process)

Defrost end temperature (probe 2) (If P4 ¹ 1)

Defrost on equipment start-up

0=NO, First defrost as per d0

1=YES, First defrost as per d6

Defrost start delay on equipment start-up

Calculated time between defrost period :

0=Total actual time; 1 =Sum of times the compressor is on

Drip time at end of defrost

(compressor and fans off) (if P4 ¹ 1)

Exit to Level 1

FAN CONTROL

Description

F0 Fan shut-down temperature as per probe 2 (if P4 ¹ 1)

FAn

F1 Probe 2 differential (If P4 ¹ 1)

F2 Stop fans when stopping compressor 0=No, 1=Yes

F3 Fan status during defrost: 0=Parados; 1=En marcha

Starting delay after defrost (if F3=0)

Will only operate if it is higher than d9

EP Exit to Level 1

Technical specifications

Rated voltage Un .............................................................400 V~ ±10 % 50/60 Hz ±5 %

Rated voltage Ue.................................................................230 V~ ±10 % 50/60 Hz ±5 %

Maximum nominal input current .................................................................................32 A

Short-circuit current at the connection point.................................................................6 kV

Probe temperature range......................................................................–45.0 ºC to 99.9 ºC

Resolution, setting and differential ...........................................................................0.1 ºC

Thermometric precision............................................................................................± 1 ºC

Precision of the NTC probe at 25 ºC ........................................................................± 0.4 ºC

Input for NTC probe ........................................................................................AKO-14901

Maximum input power in the operation .....................................................................30 VA

Working ambient temperature.......................................................................-5 ºC to 40 ºC

To access it, press the

Value Min. Def. Max.

0.0

ºC / ºF

-45

A0 Configuration of temperature alarms : 0=Relative to SP

ºC / ºF

-20.0

0.0

20.0

A1 Maximum alarm probe 1 (must be greater than SP)

0.1

2.0

20.0

A2 Minimum alarm probe 1 (must be greater than SP)

ºC / ºF

A3 Temperature alarm delay during start-up

ºC / ºF

A4 Temperature alarm delay after completion of a defrost

ºC / ºF

-45

A5 Temperature alarm delay after reaching the value of A1 or A2

A6 External alarm delay when receiving digital input signal (P10 or P11=2 or 3)

A8 Show warning if defrost is terminated by time-out 0=No, 1=Yes

min.

120

A10 Temperature Alarm Differential (A1 and A2)

A12 Door open alarm delay (if P10 or P11=1)

min.

120

CnF

min.

120

ºC / ºF

C3-SP 0.0 C2-SP

Value Min. Def. Max.

min.

255

P10

min.

255

P11

ºC / ºF

-45

8.0

99.0

P12

P13

min.

255

P14

P15 Maximum pump down time (0=Disabled)

min.

255

P23 Stop evaporator fans and compressor on opening door 0=No 1=Yes

P24 Start up delay for fans and compressor with door open

P26 Pump Down 0=Without pump down 1=With pump down

Value Min. Def. Max.

(ºC/ºF)

-45

99.0

(ºC/ºF)

0.1

2.0

20.0

tid

PU Control board software version(Information)

(min.)

PUd Display board software (Information)

Prd Display board software review (Information)

Storage ambient temperature .....................................................................–30 ºC to 70 ºC

Overvoltage category ................................................................................II s/ EN 61439-1

Degree of pollution ...................................................................................II s/ EN 61439-1

Degree of protection ..................................................................................................IP65

Dimensions AKO-17635-1 / 17635-2..............................400(An) x 300(Al) x 165(P) mm

Double isolation between power supply, secondary circuit and relay output.

Type of assembly...........................................................................................Fixed internal

Programming key compatible ......................................................................AKO-D14918

Encapsulated assembly

key for 10 seconds. The Def. column shows factory-set default parameters.

ALARM CONTROL

Description

Deactivation delay of the external alarm when the signal of the digital input

disappears (P10 or P11=2 or 3)

Exit to Level 1

GENERAL STATUS

Description

Delay of all functions on receiving electrical power

Función del código de acceso (password)

0= Inactivo; 1= Bloqueo acceso a parámetros; 2= Bloqueo del teclado

Configures the default factory settings

0= No changes 1=Return to default settings

Selection of type of inputs

1=Sonda S1 2=Sondas S1 + S2

Temperature display mode

0=Integers in ºC

1=One decimal in ºC

2=Integers in ºF

3=One decimal in ºF

Probe to be displayed (as per parameter P4)

0=visualization of all the probes in sequence; 1=Probe 1 2=Probe 2

Configuring digital input 1 0= Off

1= Door contact

2= External alarm

3= Severe external alarm

4= Change Set Point

5=Remote defrost

Configuring digital input 2 0= Off

1= Door contact

2= External alarm

3= Severe external alarm

4= Change Set Point

5=Remote defrost

Digital input polarity 1

0=Energised on closed contact, 1=Energised on open contact

Digital input polarity 2

0=Energised on closed contact, 1=Energised on open contact

Maximum start-up time after pump down

(Values between 1 and 9 seconds are not accepted) (0=Disabled)

Exit to Level 1

ACCESS CONTROL AND INFORMATION (tid)

Description

Access code (Password)

Control board software review (Information)

Exit to Level 1

1763H502 Ed.01

Value Min. Def. Max.

1=Absolute

(ºC/ºF)

99,0

(ºC/ºF)

-45

(min.)

120

(min.)

120

(min.)

120

(ºC/ºF)

0,1

1,0

20,0

(min.)

120

Value Min. Def. Max.

(min.)

255

(seg.)

120

(min.)

999

Value Min. Def. Max.