Dobinsons BU59-3506 Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник з монтажу для Автомобільні аксесуари Dobinsons BU59-3506. Dobinsons BU59-3506 8 сторінок. Bullbar for toyota landcruiser 76,78,79 series v8

Друкувати сторінку

Fitting Guide

1. Remove the number plate.

2. Remove the bumper bar and bumper re-

enforcement or factory bullbar if fitted.

3. Install the bullbar mounting bracket and

winch mounting frame as per the diagram on

page 3. Ensure the outer bullbar brackets

(item 1) are spread as wide as possible and

then tighten all bolts.

4. Carefully un-wrap the bulbar taking care not

to scratch it especially on the top loops.

Reinstall the number plate. If installing driving

lights to the bullbar it is easiest to install now.

5. If not installing a winch skip to step 13.

6. See the Installation section of your Dobinsons

4x4 Winch manual for specific detailed fitting

instructions. For a brief overview see the

following steps.

7. Test fit your winch to the mounting bracket

and do up loosely with the clutch handle on

the left hand side of the vehicle.

8. This may require the clutch handle and gear-

box housing to be rotated forward one or 2

bolt holes to allow easy access through the

bulbar holes. See instructions in winch user

manual.

9. Determine where the winch control box will

be located and mount the control box. See

instructions in winch user manual for control

box mounting options. If mounting to the top

of the bullbar using the supplied bracket,

check clearance of control box to grill and also

check where the wires will route as if the

wires are passing through the holes in the top

of the bullbar the control box may not be able

to be wired until the bullbar has been fitted as

below.

10. Wire the winch up as per the winch

instruction manual and bolt the winch to the

mounting bracket, ensure the mounting bolts

are not too long and tighten correctly. Route

the wires and connect to battery and also

route the breather hose.

Dobinsons Springs and Suspension

11. Unwind some cable from the winch, and pass

the cable through the fairlead hole in the

bullbar and through the roller fairlead. This

may require removing a circlip from the

fairlead and re installing once the cable is

passed through.

12. Install the roller fairlead into the bulbar.

13. Check the poly bulbar over riders, fog light

and top loop bolts are tight (Do not over

tighten the stainless steel loop mounting

bolts. Do not over tighten the poly bullbar

over riders as they will pull the over riders out

of shape).

14. Wire up the lights. Using a multimeter or test

light first locate the earth wire, parker positive

and indicator positive wires from the wiring

on the back of the original vehicle lights on

each side.

15. Unclip the wiring from the indicator/parker

lights. Check that the wiring will be long

enough to reach the new bullbar

indicator/parker lights and extend if required.

Using the diagram at the end of this manual,

join the corresponding wires to original

vehicle wires located in the previous step. The

wires can be joined by either using good

quality snap lock crimp connectors or by

soldering. Ensure the connection is secure and

is sufficiently insulated.

16. If fitting a bullbar with fog lights, the fog lights

can be connected using the original vehicle

fog light wires if fitted. If required, cut the old

fog light wiring plugs off and cut the new fog

light wiring plugs and join. If the vehicle is not

fitted with OEM fog lights the wiring loom

supplied can be used. Follow the wiring

diagram at the end of this manual.

17. With help, fit the bulbar into position and

install nuts and bolts supplied.

18. Align the bar with the vehicle into its correct

position.