Ashland PS Series Посібник з експлуатації, продуктивності та технічних характеристик - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з експлуатації, продуктивності та технічних характеристик для Водяний насос Ashland PS Series. Ashland PS Series 18 сторінок. Anodized aluminum sump pump
Друкувати сторінкуBefore installation, read the following instructions care-
fully. Failure to follow instruction and safety information
could cause serious bodily injury, death and/or property
damage. Each Ashland Pump is individually factory tested
to ensure proper performance. Closely following these
instructions will eliminate potential operating problems
assuring years of trouble-free service.
Most accidents can be avoided by using common sense.
IMPORTANT - Ashland Pump is not responsible for
losses, injury or death resulting from failure to observe
these safety precautions, misuse, abuse or misapplica-
tion of pumps or equipment.
All returned products must
DANGER
be cleaned, sanitized, or
decontaminated prior to shipment, to
ensure employees will not be exposed to
health hazards in handling said materials.
All applicable laws and regulations shall apply.
Bronze/brass fitted pumps may
WARNING
contain lead levels higher than con-
sidered safe for potable water systems. Government
agencies have determined that leaded copper alloys
should not be used in potable water applications.
Installation, wiring, and junction
WARNING
connections must be in accord-
ance with the National Electric Code and all applicable
state and local codes. Requirements may vary depend-
ing on usage and location.
Installation and servicing is to be
WARNING
conducted by qualified personnel only.
Rotating machinery. Amputation
DANGER
or severe lacerations can
result. Keep clear of suction and
discharge openings. DO NOT insert fingers
into pump with power connected.
Always wear eye protection when
WARNING
working on pumps. Do not wear loose
clothing that may become entangled in moving parts.
Pumps build up heat and
DANGER
pressure during operation.
Allow time for pumps to cool before handling or ser-
vicing.
Hazardous Voltage can shock,
DANGER
burn or cause death. This pump is
not intended for use in swimming pools or
water installations where human contact with
pumped fluid is possible.
Risk of electrical shock. To
DANGER
reduce risk of electrical shock,
always disconnect pump from power source
before handling. Lock out power & tag.
Sump Pumps
Model: PS Series
Specifications
WARNING
factures recommended maximum performance, as this
could cause the motor to overheat.
WARNING
illness or disease. Wear adequate protective clothing
when working on a used pump or piping. Never enter
a basin after it has been used.
WARNING
waste disposal unit or toilet: Seafood Shells, Aquarium
Gravel, Cat Litter, Plastic Objects, Sanitary Napkins or
Tampons, Diapers, Rags, Disposable Wipes or Cloth,
Medications, Flammable Material, Oil or Grease,
Strong Chemicals, Gasoline.
•
•
•
•
•
•
OVERLOAD PROTECTION
This pump series has a built in thermal protection switch,
it will protect motor from burning out due to overheating/
overloading. When motor cools down, overload protector
will automatically reset and start motor.
If overload trips frequently, check for cause. It could be a
stuck impeller, wrong/low voltage or electrical failure in
motor. If an electrical failure in the motor is suspected,
have it serviced by a competent repairman.
2
Do Not use these pumps in water
over 145°F. Do not exceed manu-
Make sure lifting handles are securely
CAUTION
fastened each time before lifting.
Do not lift, carry or hang pump by
DANGER
the electrical cables. Damage to
the electrical cables can cause shock, burns or
death. Never handle connected power cords
with wet hands. Use appropriate lifting device.
Sump and sewage pumps often
handle materials which could cause
Failure to permanently ground the
DANGER
pump, motor and controls before
connecting to power can cause shock, burns
or death.
These pumps are NOT to be
DANGER
installed in locations classified
as hazardous in accordance with the
National Electric Code, ANSI/NFPA 70.
Do not introduce into any sewer,
either directly, or through a kitchen
Operation against a closed discharge valve will cause
premature bearing and seal failure on any pump.
Any wiring of pumps should be performed by a
qualified electrician.
Cable should be protected at all times to avoid
punctures, cuts, bruises, and abrasions-inspect
frequently.
Never handle connected power cords with wet hands.
Never let cords or plugs lie in water outside the sump pit.
These pumps are offered in a three phase and single
phase wiring configuration. Voltages will vary
according to the application and can be seen in the
tables in this manual.