Ashly neWR-5 Посібник з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з експлуатації для Пульт дистанційного керування Ashly neWR-5. Ashly neWR-5 4 сторінки. Programmable ethernet based remote control unit
Також для Ashly neWR-5: Посібник користувача (6 сторінок), Посібник з експлуатації (4 сторінок)

Друкувати сторінку

Operating Manual - neWR-5 Remote Control for NE Products

Main Control Surface

The main control surface is where the neWR-5 is named, its target NE device gets selected, any

zone deﬁ nition occurs, and where the function buttons are programmed, The neWR-5 comes with

all function buttons set to "Off". Unlike the WR-5, changes must be saved to the neWR-5 before

becoming effective.

Not all of the button functions listed below are available on all NE products, for instance an

ampliﬁ er will not have "matrix mixer" capability unless it has DSP installed, and some products do

not have logic outputs. Protea NE software is able to determine which functions are available for

neWR-5 control.

1) Off - No function assigned and the button's LED remains unlit

2) Preset Recall - A single preset number is assigned to a button. When the button is pressed,

the recalled preset number and the letters "PC" (Preset Change) are alternately ﬂ ashed on the WR-5

for ﬁ ve seconds, also locking out any other WR-5 action for that time.

3) Preset Scroll Mode - A range of presets can be assigned to a function button which when

selected, enables the up/down buttons to scroll through the available presets. Upon release of the up/

down button, the currently displayed preset will load. The function button will glow amber for the

duration of the preset scroll operation.

4) Gain Control - Since there are many possible gain adjustment points within a given NE au-

dio processing device, the neWR-5 displayed gain level is only a relative value. In other words, gain

could be changed elsewhere in the target unit, independent from neWR-5 control. The neWR-5 can

adjust gain from 0 to 99, and an upper and lower number limit can be set in the function range sec-

tion to limit the maximum and minimum reach of that control. To control the gain within the target

device's input or output signal path, the neWR-5 remote gain function must ﬁ rst be inserted into a

block in the unit's DSP controls window.

Gain Control over individual channel(s) - When a gain control button is assigned

to control one or more individual channels, pressing that button will cause it to light amber, during

which time the up/down buttons determine gain for the selected channels. If the up/down buttons

remain idle for ﬁ ve seconds, the gain button becomes inactive until being pressed again.

Gain Control over zone - If a zone output is active for that neWR-5, meaning one or

more output checkboxes are selected within the neWR-5 Zone Setup mode, the output gain for that

zone will be shown as the default numerical display, during which time the up/down buttons stay ac-

tive for that zone's overall gain control. If a button is assigned for individual input channel(s) gain

control in addition to the neWR-5 being deﬁ ned for output zone control, that button will turn amber

when pressed, and both the neWR-5 up/down buttons and display will reﬂ ect the input channel(s)

gain, reverting back to output zone gain after ﬁ ve seconds of inactivity. If there is no zone output

assigned for the neWR-5, the display shows "--" as the default.

5) Channel Engage/Mute - A button can be conﬁ gured to mute one or more inputs or outputs,

or any combination of the two. The button is green when engaged and red when the selected chan-

nels are muted.