BluePoint Fasteners GT-100L Посібник з техніки безпеки та експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Посібник з техніки безпеки та експлуатації для Цвяходер. BluePoint Fasteners GT-100L. BluePoint Fasteners GT-100L 13 сторінок. Gas concrete nailer
Друкувати сторінкуRemoving the nails:
(1) Pull the nail feeder backward. (see chart e).
Nail Feeder
chart e
(2) Let the nails drop into palm of the hand(see
chart g).
Nail Feeder
chart g
NAILER OPERATION
Read section titled "SAFETY".
DANGER
■ Operators and others in work
area MUST wear safety glasses
with side shields which conforms
to ANSI Z87.1 specifications.
■ Never use in presence of flammable liquids
or gases.
14
Do not touch around the exhaust
outlet with bare hands.
The push lever and nose will
become hot and get heated up
after prolonged or rapid use.
Do not allow push and pull lever
with hand, otherwise it may
cause accidental firing and hurt
120°F MAX
(50℃)
someone.
■ Explosion and fire hazard: Keep
away from sunshine and from
temperature exceeding 120°F
(50°C).
Keep away from ignition source.
No smoking.
WARNING
NEVER point tool at yourself or
others in work area.
K ee p f i ng e r s A WAY from
trigger when not driving nails to
avoid accidental firing.
Use outside or well- ventilated
area.
Do not inhale its contents.
not use the electrical cord if
damaged. H ave it repaired
immediately. Never place your
face, hands or feet closer than
8 inches (200 mm) from firing
head when using.
■ Do not drive nails on top of other nails or with
Nailer at too steep of an angle; nails can
ricochet and hurt someone.
■ Do not drive nails into thin boards or near
corners and edges of workpiece. Nails can be
driven through or away from workpiece and
hit someone.
■ Never drive nails from both sides of a wall at
the same time. Nails can be driven into and
through the wall and hit a person on the
opposite side.
■ Never use Nailer which is defective or
operating abnormally.
■ Do not use Nailer as a hammer.
■ Disconnect battery and fuel cell from Nailer
when:
it is not in use;
leaving work area;
moving it to another location;
handing it to another person.
■ Be careful of misfired fastener.
If the nailer cannot drive a nail at a
temperature below 23°F (-5°C), place firing
head against the workpiece and quickly press
downward nailer 2~3 times, pulling the trigger,
the nails will be driven. Or try again after
keeping the nailer and the fuel cell indoor for
30 minutes.
This Nailer is equipped with a FULL SEQUENTIAL
ACTUATION MECHANISM.
Explanation of FULL SEQUENTIAL ACTUATION
MECHANISM nailing operation:
First, press the firing head against the workpiece;
Next, press down the nailer; Then, pull the trigger to
drive a nail.
The machine employs a preventive mechanism
that would not allow the push lever to operate if
the magazine is not loaded .
CAUTION
Use caution not to press the firing head tip against
the workpiece when the firing head cannot be
pushed back in place.
METHODS OF OPERATION
Do
This Nailer is equipped with the firing head and does
not operate unless the firing head is held
perpendicular to the work surface.
It is intermittent operation (Trigger fire) only.
2. Press the
Firing Head
against the
workpiece firmly.
(1)Position the nail outlet on the workpiece with
finger off the trigger.
(2)Depress the firing head firmly until it is
completely depressed.
(3)Pull and squeeze the trigger to drive a nail.
(4)Remove finger from the trigger.
To continue nailing in a separate location, move
the nailer along the workpiece, repeating above
steps (1) -(4) as required.
Nail Jam Removal
If the nail gets jammed, remove it by following
these steps:
(1) Remove the fuel cell and the battery;
Fuel Cell
(2) Remove all nails;
(3) Loosen the lock bolt;
(4) Take off the magazine assembly, remove the
jammed nails;
3. Press
the Trigger
(5) Fit on the magazine assembly, tighten the lock
bolt, reinsert the fuel cell and battery pack, then
continue firing.
Battery Pack
Nail
Lock Bolt
Magazine
Assembly
15