Blueprint PNGCP18003 Посібник з програмування - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з програмування для Панель керування Blueprint PNGCP18003. Blueprint PNGCP18003 5 сторінок.
Друкувати сторінку
CONTROL PANEL
PNGCP18003
PNGCP18004
PROGRAMMING MANUAL
SLIDE SWITCH SETTINGS:
1. Press and hold Auxiliary Push-Button "1" and "4" until slide
switch #2 indicator LED flashes.
2. Press Auxiliary Push-Button "1", "2" or "3" depending on
which configuration for the slide switch is required.
SLIDE SWITCH SETTINGS
AUXILIARY PUSH-BUTTON 1
1
IS SELECTED
AUXILIARY PUSH-BUTTON 2
2
IS SELECTED
AUXILIARY PUSH-BUTTON 3
3
IS SELECTED
Setting PA Volume:
1. Press and Hold Auxiliary Push-Button "1" and "2" until slide switch
#2 and #3 indicator LED flashes.
2. Depress and hold PA switch on microphone and press Push-Button
"1"-"8" depending on volume required. When correct
volume is determined, press Radio Rebroadcast and the
volume setting will be permanently stored.
LOW
2
3
4
5
6
7
HIGH
BACKLIGHT INTENSITY:
While pressing RADIO REBROADCAST BUTTON,
press Auxiliary Push-Button "1"-"8" to adjust backlight intensity.
"1" = Lowest intensity, "8" = Highest intensity.
Backlight must be enabled by the Gray wire on CN6.
1.800.338.7337 / www.soundoffsignal.com
Pg. 2
ALTERNATE MODES:
1. Press and Hold Auxiliary Push-Button "2" and "6" until Slide
Switch indicator #1 and #2 LED flashes.
1
. Alternate Horn Ring control: Custom operation of vehicle
horn when pressed. Refer to figure below for details.
2
. Alternate Horn Ring control option: (Alternate Horn Ring
Control must be enabled). Custom operation of vehicle
horn when pressed. Refer to figure below for details.
1
2
STANDBY
3
LEVEL 1
1
LEVEL 2
2
3
LEVEL 3
1
2
3
* Set in "Other Modes" 6. Horn Ring Standby Tone
3.
GUN LOCK SECURITY:
6.
DISABLE RELAY ERROR FOR AUX 7 & 8:
ON = Enabled
OFF = Disabled
ON = Option 2
OFF = Option 1
ALTERNATE HORN RING CONTROL
OPTION 1
OPTION 2
OEM HORN
OEM HORN
OEM HORN
OEM HORN
Air Horn or Wail
Tap to Turn On Warning Tone,
Button Tone while
Tap again to Change Warning
Pressed *
Tone. Press and Hold for Air
Horn Tone
Tap to turn ON
TONE
TONE
Warning Tone, Tap
SWITCH OFF:
SWITCH ON:
again to change
Air Horn Tone
Tap to change
Warning Tone. Press
or Wail Button
Warning Tone,
and Hold for Air Horn
Tone while
Press and Hold
Tone
Pressed *
for Air Horn
Tone
ON = Operator must press Standby button
within 1 second after pressing 8
second time delay button to active
switch
OFF = 8 second time delay switch is
activated immediately when
pressed
ON = Disable fault detect indication for
Aux relays 7& 8.
OFF = Fault detect normal.
7. Slide Switch Enabled Without Ignition: After ignition
is turned off, device will stay on in lower power mode and allow
(ONLY) the slider to operate.
ON = With ignition off, slider relays will
still turn on if slider is in position 1,
2, or 3.
OFF =Device turns off normally, sliders
will not work when off.
8. Invert Backlight Color: Swap the background and active
colors of buttons.
ON = Backlight color is green, active is
red.
OFF = Backlight color is red, active is
green.
OTHER MODES:
Press and Hold Auxiliary Button "1" and "5" until slide switch #1
and #3 indicator LED flashes.
1. Horn Ring Activation: Determines when pressing the Vehicle
Horn will activate siren tone
ON = Enabled whenever siren is ON
OFF = Enabled only when slide switch
is in level position 3
2. Buzzer: Audible tone from control panel whenever operator
presses push-button or changes position of slide/rotary
switch
ON = Buzzer enabled
OFF = Buzzer disabled
3. Speakers Diag LED disable: Disabling Diagnostic LED does
not turn off secondary speaker channel
ON enable Diagnostic LED (200W)
OFF disable Diagnostic LED (100W)
4. Horn Ring Latch Mode: (Alternate Horn Ring Control Must
be Disabled) Activates the siren tone per scroll mode off
settings when operator momentarily presses on Vehicle
Horn. *Wail Only. Only works when tone is already
active. (See Horn Ring Table).
ON = Horn ring Toggle Switch Mode
OFF = Horn ring Momentary Switch
Mode
PNGCP1800(x) 0419