Blueprint PNGCP18004 Посібник з програмування - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник з програмування для Панель керування Blueprint PNGCP18004. Blueprint PNGCP18004 5 сторінок.
Друкувати сторінку
CONTROL PANEL
PNGCP18003
PNGCP18004
PROGRAMMING MANUAL
OTHER MODES CONTINUED:
5. Power Down: Determines siren operation after ignition wire input
has no voltage
ON = Timed Power Down: Siren will
power down 10 min. after last
activity.
OFF = Immediate Power Down: Siren
will power down immediately
after ignition is turned off.
6. Horn Ring Standby Tone: (Alternate Horn Ring Control Must be
Disabled) Determines which tone to output when siren is in
standby and vehicle horn is pressed
ON = Air Horn Tone
OFF = Manual Button Tone
7. 8 Second Buzzer Alert: Provides audible beep every 8 seconds
whenever any auxiliary switches are ON or level 1,2, or 3 is
active.
ON = Enabled
OFF = Disabled
8. Air Horn Button Output Channels
ON = In standby mode, Horn tone is
output on Spkr A & B. When
Warning Tone is Active,
Warning Tone continues on Spkr
A & Air Horn Button Tone is
output on Spkr B.
OFF = Horn Button Tone always
produced on Spkr A & B.
1.800.338.7337 / www.soundoffsignal.com
Pg. 3
PROGRAMMING MODES
AUXILIARY SWITCH SETTINGS:
Refer to Siren Amplifier Diagnostic Indicator Chart below for Button and LED
locations and terminology
1. Press and Hold Auxiliary Button #1 and #8 until slide switch #1 LED
flashes.
2. Press the button which setting is going to be viewed/changed 1 time.
3. Monitor the 5 LED's for the arrow controller to determine setting
- *Arrow Controller (Left, Right, Center, OFF), Dual Output; 1 & 9
- Alternate Action Switch (Press ON / Press OFF)
- Momentary Action Switch (ON only when depressed)
- 8 Second ON Time (ON for 8 seconds when depressed)
- Level 1 Disable (Turns OFF Level 1 Output)
- Level 2 Disable (Turns OFF Level 2 Output)
- Left Arrow, Single Output
- Right Arrow, Single Output
- Center Arrow, Single Output
- Warning Bar Output
*Can only be programmed to one button
and will disable Left, Right and Center
Arrow Single Outputs if they are used.
4. Press and release button until desired mode is selected.
5. Continue steps 2-3 for any other buttons that need to be programmed.
Default Settings:
Button #1:
Arrow Controller
Button #2-7: Alternate Action Switch
Button #8:
8 Second ON Time
Denotes Factory Default Setting
SIREN AMPLIFIER DIAGNOSTIC
INDICATORS:
DIAG
S1
S2
FLASHING
OFF
ON
FLASHING
ON
OFF
FLASHING
FLASHING
-
FLASHING
-
FLASHING
FLASHING
FLASHING
FLASHING
COMM FAULT -RELAY AND AMP
-
-
-
*OFF
ON
-
*OFF
-
ON
*OFF
OFF
-
*OFF
-
OFF
Slide switch mapping programming:
Allows the operator to have the siren automatically turn on auxiliary
push-buttons or tones based on the position of the slide switch.
If an auxiliary or tone push-button is programmed to turn ON when
the slide switch position is selected, the auxiliary push-button
will turn OFF when the programmed slide switch position is no
longer selected.
The operator can override the automatic activation of the auxiliary
push-button by momentarily pressing the auxiliary push-button.
To program:
1. Press auxiliary push-buttons '4' and '5' for until Radio
Rebroadcast indicator LED flashes.
2. Move slide switch to desired position.
3. Press auxiliary push-buttons '1' – '8' and or Siren Control Select
as required.
LED ON
(GREEN)
LED OFF
(RED OR OFF)
4. Repeat steps 2 and 3 for other slide switch positions as
required.
5. Place appropriate button legend over activity indicator for each
programmed button.
* SIREN AUDIO BUTTON ACTIVATED
(EXCEPT RADIO REBROADCAST)
CONDITION
UNDER-VOLTAGE
OVER-VOLTAGE
COMM FAULT - RELAY
COMM FAULT - AMP
-
SPKR 1 IS ACTIVE
SPKR 2 IS ACTIVE
SPKR 1 IS NOT-FUNCTIONING
SPKR 2 IS NOT-FUNCTIONING
Auxiliary push-button or Siren Control Select
will automatically turn ON when level switch
position is activated.
Auxiliary push-button or Siren Control Select
will NOT automatically turn ON when level
switch position is activated.
PNGCP1800(x) 0419