Asko D3122 Інструкція з монтажу Посібник з монтажу - Сторінка 9
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Посудомийна машина Asko D3122. Asko D3122 12 сторінок. D3122 use & care guide fr (french ucg 2+1 warranty)
Також для Asko D3122: Інструкція з використання та догляду (16 сторінок), Посібник із швидкого старту (2 сторінок), (іспанська) Uso y Cuidado (16 сторінок), (Французькою) Мануель Д'ультізі (Manuel D'utilisation) (16 сторінок)
Друкувати сторінку
ADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGS
Now that all the connections are made and the machine
is in place under the cabinet, you should make the final
height adjustment.
1. You should set the
rear foot first. To do
this,
use
a
screwdriver to rotate
the adjusting screw
on the bottom front of
the machine. Turn the
screw clockwise to
raise the foot and
counterclockwise to lower it.
FASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINET
It's necessary to fasten the dishwasher to the cabinet
so it won't tilt when the door is opened or if something
heavy is placed on the door. Use only screws provided
with the machine.
1.
Use option A for U.S. or European standard
installations. Use option B only for European
standard installations.
2.
Cover the screw heads with the
plastic plugs provided with the
machine.
3.
When the machine is properly
attached, check that the feet are
tight against the floor and that the
machine is level.
INST
INST
INSTALLING
ALLING THE
ALLING
ALLING
INST
INST
ALLING
SETTING
SETTING
SETTING THE
SETTING
SETTING
THE T T T T T OE KICK
THE
THE
THE
DEPTH
DEPTH
DEPTH
DEPTH
DEPTH
1.
Press the grey catches
toward each other to
release the bracket.
2.
Pull out the holders as
far as required.
3.
Press in the catches so
that
they
lock
brackets in place.
4.
Hang the toe kick onto the holders by inserting it
into the grooves.
Mounting
Screws
THE T T T T T OE KICK
THE
THE
OE KICK
OE KICK
OE KICK
THE
OE KICK
OE KICK
OE KICK
OE KICK
OE KICK
the
2. Using a 1/2" (12 mm) wrench, adjust the locking
nuts until the machine is
level. (The machine may
have an inclination of 1/4"
maximum without affecting
its performance.)
3. When the feet are properly adjusted, tighten the
locking nuts to the base pan.
B
A
NOTE:
When it is not possible to attach the dishwasher
to the cabinet, you should install tip guards.
(See "Tip Guards" on page 2.)
Once you have the toe kick bracket in place, you can
install the toe kick, as follows:
1.
Lay the insulation on the back side of the toe kick to
make sure it fits properly.
2.
Peel the adhesive protection strip off the insulation
and press it firmly to the back side of the toe kick,
making sure you don't cover any slots on the toe
kick.
3.
Positioning the notches on the toe kick at the edge
of the access panel, slide the toe kick up behind
the access panel then let it slide to the floor.
4.
Adjust the toe kick depth.
B
A
Page 9