Ekinex EK-GC1-TP Schnellstart-Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Controller Ekinex EK-GC1-TP herunter. Ekinex EK-GC1-TP 4 Seiten. Led dimmer-actuator 4 channels rgbw
12..30 VDC
12..30 VDC
+
-
+
1
2
6
7
Area
Line
Dev.
bus KNX
1) Selected parameter / channel indication
2) Selected parameter / channel change
3) Parameter / output selection pushbutton
4) Operating mode LED
5) Current modification mode LED
6) Programming pushbutton
7) Programming LED
Thanks to the pushbuttons located on the front of the
device, the connected loads can be manually controlled
when the programming has not yet been carried out.
Pressing the pushbuttons (+, −) for manual control of the
output increases or decreases the light intensity or the
value of the respective output or parameter.
Display elements
• Red LED (7) to display the active operating mode of
the device (on = programming, off = normal operation)
• Green LEDs (1) to display the selected channel or
operation mode
• Green LED (5) to display the current modification
mode (output channel or color parameter)
• Red LED (4) to display the operating mode (on = ma-
nual operation, off = automatic operation)
Mounting
The device has degree of protection IP20, and is there-
fore suitable for use in dry interior rooms. The housing is
made for rail mounting according to EN 60715 in boards
or cabinets for electrical distribution. The installation is in
horizontal position, the correct position is when the KNX
bus terminal and the 230 Vac terminals are located at the
bottom and the terminals for the outputs are located at
the top.
For the installation of the device on the rail proceed as
follows:
• with the aid of a tool bring the locking device in the
fully lowered position (a);
• place the upper edge of the rear inner profile on the
upper edge of the rail (b);
• rotate the device towards the rail (c);
• push the locking device upward until it stops and locks
the device in place (d).
Before removing the device, be sure the outputs and their
power supply have been disconnected, and the bus ter-
minal has been extracted from its slot. Use a screwdriver
to slide down the locking device and remove the device
from the rail.
C1/R
C2/G
C3/B
C4/W
-
-
-
-
-
3
5
4
230V~/6A max
1
3
i
Note. It is recommended that the installation of the
device always ensure the full accessibility of the
front side i to allow the operation of the pushbuttons.
Connection of the KNX bus line
The connection of the KNX bus line is made with the ter-
minal block (black / red) included in delivery and inserted
into the slot of the housing.
Characteristics of the KNX terminal block
• spring clamping of conductors
• 4 seats for conductors for each polarity
• terminal suitable for KNX bus cable with single-wire
conductors and diameter between 0.6 and 0.8 mm
• recommended wire stripping length: approx. 5 mm
• color coding: red = + (positive) bus conductor, black
= − (negative) bus conductor
!
Warning! In order to supply the KNX bus lines use
only KNX bus power supplies (e.g. ekinex EK-AB1-
TP or EK-AG1-TP). The use of other power supplies
can compromise the communication and damage
the devices connected to the bus.
Connection of loads and output power
The connection of the loads and their power supply is
made through the screw terminals located on the top side
of the device.
Characteristics of the terminals
• cage clamping of conductors
• maximum cross section of conductor 2.5 mm² (single-
wire) or 1.5 mm² (multi-wire)
• recommended wire stripping approx. 6 mm
• torque max 0,8 Nm
!
Warning! The electrical connection of the device
substances. can be carried out only by qualified
personnel. The incorrect installation may result in
electric shock or fire. Before making the electrical
connections, make sure the power supply has been
turned off.
Connection of the auxiliary contact
The connection of the auxiliary contact is made through
the screw terminals located on the bottom side of the de-
vice.
2
2
4