Ekinex EK-GC1-TP Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Ekinex EK-GC1-TP. Ekinex EK-GC1-TP 4 pagina's. Led dimmer-actuator 4 channels rgbw

Pagina afdrukken

12..30 VDC

Area

Line

Dev.

bus KNX

1) Selected parameter / channel indication

2) Selected parameter / channel change

3) Parameter / output selection pushbutton

4) Operating mode LED

5) Current modification mode LED

6) Programming pushbutton

7) Programming LED

Thanks to the pushbuttons located on the front of the

device, the connected loads can be manually controlled

when the programming has not yet been carried out.

Pressing the pushbuttons (+, −) for manual control of the

output increases or decreases the light intensity or the

value of the respective output or parameter.

Display elements

• Red LED (7) to display the active operating mode of

the device (on = programming, off = normal operation)

• Green LEDs (1) to display the selected channel or

operation mode

• Green LED (5) to display the current modification

mode (output channel or color parameter)

• Red LED (4) to display the operating mode (on = ma-

nual operation, off = automatic operation)

Mounting

The device has degree of protection IP20, and is there-

fore suitable for use in dry interior rooms. The housing is

made for rail mounting according to EN 60715 in boards

or cabinets for electrical distribution. The installation is in

horizontal position, the correct position is when the KNX

bus terminal and the 230 Vac terminals are located at the

bottom and the terminals for the outputs are located at

the top.

For the installation of the device on the rail proceed as

follows:

• with the aid of a tool bring the locking device in the

fully lowered position (a);

• place the upper edge of the rear inner profile on the

upper edge of the rail (b);

• rotate the device towards the rail (c);

• push the locking device upward until it stops and locks

the device in place (d).

Before removing the device, be sure the outputs and their

power supply have been disconnected, and the bus ter-

minal has been extracted from its slot. Use a screwdriver

to slide down the locking device and remove the device

from the rail.

C1/R

C2/G

C3/B

C4/W

230V~/6A max

Note. It is recommended that the installation of the

device always ensure the full accessibility of the

front side i to allow the operation of the pushbuttons.

Connection of the KNX bus line

The connection of the KNX bus line is made with the ter-

minal block (black / red) included in delivery and inserted

into the slot of the housing.

Characteristics of the KNX terminal block

• spring clamping of conductors

• 4 seats for conductors for each polarity

• terminal suitable for KNX bus cable with single-wire

conductors and diameter between 0.6 and 0.8 mm

• recommended wire stripping length: approx. 5 mm

• color coding: red = + (positive) bus conductor, black

= − (negative) bus conductor

Warning! In order to supply the KNX bus lines use

only KNX bus power supplies (e.g. ekinex EK-AB1-

TP or EK-AG1-TP). The use of other power supplies

can compromise the communication and damage

the devices connected to the bus.

Connection of loads and output power

The connection of the loads and their power supply is

made through the screw terminals located on the top side

of the device.

Characteristics of the terminals

• cage clamping of conductors

• maximum cross section of conductor 2.5 mm² (single-

wire) or 1.5 mm² (multi-wire)

• recommended wire stripping approx. 6 mm

• torque max 0,8 Nm

Warning! The electrical connection of the device

substances. can be carried out only by qualified

personnel. The incorrect installation may result in

electric shock or fire. Before making the electrical

connections, make sure the power supply has been

turned off.

Connection of the auxiliary contact

The connection of the auxiliary contact is made through

the screw terminals located on the bottom side of the de-

vice.