DoorKing MicroCLICK 8059 Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Empfänger DoorKing MicroCLICK 8059 herunter. DoorKing MicroCLICK 8059 3 Seiten. Rf receiver (wiegand)

How Receiver Functions
The 8059 receiver responds to the MicroCLIK™ transmitter code is defined by "Facility Codes"
and "Transmitter Button Codes". For example: an 8059 receiver can be programmed to
respond to only the first button on a multiple button MicroCLIK™ transmitter while a
second 8059 receiver can be programmed to respond to only the second button of
the same multiple button MicroCLIK™ transmitter. Thus allowing a single multiple
button MicroCLIK™ transmitter to activate two different receivers without fear of
both receivers responding to the same transmitter code. Like wise one receiver
can be programmed to respond to a specific facility code while another can be
programmed for a different facility code. In Wiegand output mode, you have the
option of matching or ignoring the facility code to allow the receiver to activate.
There are seven receiver programming functions:
1. Regular Transmitter Programming
2. 26-bit Wiegand Programming (Factory Setting)
3. 31-bit Wiegand Programming
1. Regular Transmitter Programming
Press and hold the Programming Button or the "Master Transmitter Button" (if existing, see above) until the programming LED quickly flashes ONE
time (about 2 seconds), then release the button. The programming LED will flash once every second indicating that you are in the transmitter
programming mode....
Press and
START
Hold Button
....While the programming LED is flashing, activate each of the MicroCLIK™ transmitters that will be used (If you are using a two or three button
transmitter, make sure to press the correct button). There are three (3) different "2-Button" MicroCLIK™ transmitter button combinations that each
receiver can be programmed to respond to: button-1, button-2 and buttons 1&2 pressed at the same time. There are six (6) different "3-Button"
MicroCLIK™ transmitter button combinations that each receiver can be programmed to respond to: button-1, button-2, button-3, buttons 1&2
pressed at the same time, buttons 2&3 pressed at the same time and buttons 1&3 pressed at the same time. A maximum of 80 transmitters codes
can be stored in this receiver. Each button or combination of buttons pressed is counted as ONE transmitter code.
Once the desired transmitter codes have been stored into the receiver memory, the receiver will automatically exit the programming mode when no
more transmitter codes are received (approx. 10 seconds idle time). The LED will come on for 3 seconds and then go out.
All Desired
1 Sec.
MicroCLIK™ Transmitters
have been Activated
Transmitter Programming Mode
When Using Wiegand Functions
At least one transmitter code must be programmed into the receiver memory, allowing the receiver to respond to the facility code and transmitter
button code that will be used. This step is necessary so that the receiver knows which transmitter button to respond to. For example, if a (2) two
button transmitter code is programmed into the receiver pressing only button-2, the receiver will only respond to transmitter codes initiated by
button-2. To have a receiver respond to both buttons, you can program the transmitter code into the receiver twice, using button-1 first, and then
button-2. If using more than one facility code or if the receiver is to respond to different transmitter buttons, simply add additional transmitters,
refer to 1. Regular Transmitter Programming. The receiver will allow the facility code to be ignored when using a Wiegand controller if desired.
2. 26-bit Wiegand Programming
Press and hold the Programming Button and follow the flashing LED sequence as shown below, then release the button. The programming LED
will flash once for 3 seconds indicating that the receiver is in 26-bit Wiegand output mode.
Press and
Hold Button
4. Match Facility Code Programming
5. Ignore Facility Code Programming
6. Erase ALL Transmitter Codes
7. Master Transmitter Programming
2 Sec.
Release
Button
One Quick Flash
Approximately 10 Seconds Idle Time
1 Sec.
Release
One Flash
Two
Approximately 4 Sec.
Less than 10 Seconds Idle Time
1 Sec.
1 Sec.
1 Sec.
Transmitter Programming Mode
1 Sec.
1 Sec.
One
3 Second
Flash
The receiver is now in
Button
26-bit Wiegand Output Mode
One 3 Second
Flash
Programming LED: Will
flash sequences during
programming and
flashes during normal
operation or frequency
interference.
Wiegand LED's: Will blink
as Wiegand data is being
transmitted.
Activate All Desired
1 Sec.
1 Sec.
MicroCLIK™ Transmitters
FINISH
Inglewood, California 90301
n
t t o
B u
i n g
m m
g r a
P r o
120 Glasgow Avenue
U.S.A.