DoorKing MicroCLICK 8059 Quick Start Manual - Page 2

Browse online or download pdf Quick Start Manual for Receiver DoorKing MicroCLICK 8059. DoorKing MicroCLICK 8059 3 pages. Rf receiver (wiegand)

Print Page

How Receiver Functions

The 8059 receiver responds to the MicroCLIK™ transmitter code is defined by "Facility Codes"

and "Transmitter Button Codes". For example: an 8059 receiver can be programmed to

respond to only the first button on a multiple button MicroCLIK™ transmitter while a

second 8059 receiver can be programmed to respond to only the second button of

the same multiple button MicroCLIK™ transmitter. Thus allowing a single multiple

button MicroCLIK™ transmitter to activate two different receivers without fear of

both receivers responding to the same transmitter code. Like wise one receiver

can be programmed to respond to a specific facility code while another can be

programmed for a different facility code. In Wiegand output mode, you have the

option of matching or ignoring the facility code to allow the receiver to activate.

There are seven receiver programming functions:

1. Regular Transmitter Programming

2. 26-bit Wiegand Programming (Factory Setting)

3. 31-bit Wiegand Programming

1. Regular Transmitter Programming

Press and hold the Programming Button or the "Master Transmitter Button" (if existing, see above) until the programming LED quickly flashes ONE

time (about 2 seconds), then release the button. The programming LED will flash once every second indicating that you are in the transmitter

programming mode....

Press and

START

Hold Button

....While the programming LED is flashing, activate each of the MicroCLIK™ transmitters that will be used (If you are using a two or three button

transmitter, make sure to press the correct button). There are three (3) different "2-Button" MicroCLIK™ transmitter button combinations that each

receiver can be programmed to respond to: button-1, button-2 and buttons 1&2 pressed at the same time. There are six (6) different "3-Button"

MicroCLIK™ transmitter button combinations that each receiver can be programmed to respond to: button-1, button-2, button-3, buttons 1&2

pressed at the same time, buttons 2&3 pressed at the same time and buttons 1&3 pressed at the same time. A maximum of 80 transmitters codes

can be stored in this receiver. Each button or combination of buttons pressed is counted as ONE transmitter code.

Once the desired transmitter codes have been stored into the receiver memory, the receiver will automatically exit the programming mode when no

more transmitter codes are received (approx. 10 seconds idle time). The LED will come on for 3 seconds and then go out.

All Desired

1 Sec.

MicroCLIK™ Transmitters

have been Activated

Transmitter Programming Mode

When Using Wiegand Functions

At least one transmitter code must be programmed into the receiver memory, allowing the receiver to respond to the facility code and transmitter

button code that will be used. This step is necessary so that the receiver knows which transmitter button to respond to. For example, if a (2) two

button transmitter code is programmed into the receiver pressing only button-2, the receiver will only respond to transmitter codes initiated by

button-2. To have a receiver respond to both buttons, you can program the transmitter code into the receiver twice, using button-1 first, and then

button-2. If using more than one facility code or if the receiver is to respond to different transmitter buttons, simply add additional transmitters,

refer to 1. Regular Transmitter Programming. The receiver will allow the facility code to be ignored when using a Wiegand controller if desired.

2. 26-bit Wiegand Programming

Press and hold the Programming Button and follow the flashing LED sequence as shown below, then release the button. The programming LED

will flash once for 3 seconds indicating that the receiver is in 26-bit Wiegand output mode.

Press and

Hold Button

4. Match Facility Code Programming

5. Ignore Facility Code Programming

6. Erase ALL Transmitter Codes

7. Master Transmitter Programming

2 Sec.

Release

Button

One Quick Flash

Approximately 10 Seconds Idle Time

1 Sec.

Release

One Flash

Two

Approximately 4 Sec.

Less than 10 Seconds Idle Time

1 Sec.

Transmitter Programming Mode

1 Sec.

One

3 Second

Flash

The receiver is now in

Button

26-bit Wiegand Output Mode

One 3 Second

Flash

Programming LED: Will

flash sequences during

programming and

flashes during normal

operation or frequency

interference.

Wiegand LED's: Will blink

as Wiegand data is being

transmitted.

Activate All Desired

1 Sec.

MicroCLIK™ Transmitters

FINISH

Inglewood, California 90301

t t o

B u

i n g

m m

g r a

P r o

120 Glasgow Avenue

U.S.A.