AMSEC 5BE Betriebsanleitung - Seite 4
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Schlösser AMSEC 5BE herunter. AMSEC 5BE 4 Seiten. 5-button electronic lock
Seite druckenAMSEC 5-Button Electronic Lock Model 5BE Operating Instructions
The 5BE lock has a Penalty Lockout feature to prevent tamper-
ing (code testing).
•
This feature will cause the lock to stop accepting input for
five (5) minutes after four (4) incorrect opening attempts.
•
While in Penalty Lockout, the lock will respond to any key-
stroke with eight (8) rapid flashes of the red LED lamp,
along with beeps (if the beeper is turned on).
•
While in Penalty Lockout, the LED lamp will flash once
every five (5) seconds and beep (if the beeper is turned on).
When a correct code has been entered, Primary or Backup, the
Red LED Lamp will light for three (3) seconds, indicating the
lock can be opened.
•
To open the lock, turn the knob Clockwise 90 degrees.
The 5BE lock uses a standard 9VDC Alkaline Battery.
•
We recommend Duracell® or Eveready Energizer® batteries
for best performance.
•
The battery is located inside the internal lock body, at one
end, under a hatch.
•
To replace the battery, pull the hatch open and remove the
battery from the cavity. Unclip it form the terminals, and clip
on a new battery, tuck the wires in neatly and press firmly to
close the hatch.
•
The 5BE lock should open approximately 5000 times with
fresh, good quality batteries, depending on installed options
and user habits.
The 5BE lock provides a backup power port to prevent lockout if
the primary battery is allowed to go dead.
•
Under a door next to the knob on the keypad, you will find
terminals to allow connection of a fresh secondary 9VDC
battery.
Loss of power will not erase codes. The 5BE lock uses "non-
volatile" memory.
On the side of the lock body, you will find a small black button
used to program codes and features.
4
Revised February, 2005
The 5BE lock provides two auxiliary outputs for connection to
alarm or monitoring services.
•
There is a four (4) position socket in the side of the lock
body to provide connections. An optional cable is available
to plug into this port for installation connection.
•
Two outputs are provided; one for "Duress" signaling and
the other for "Open Door" signaling.
•
The outputs are solid state switches, and therefore are
polarity sensitive and can only be used to switch DC sig-
nals. Do not connect any AC power source to these ports.
•
The output ports are rated for 12 VDC, 500 mA maximum.
This lock is not waterproof, and is not intended for outdoor use.
Exposure to extreme conditions or excess moisture may cause
a malfunction, and will void the Manufacturers Warranty.
Optional Features and Operation
The 5BE lock provides two advanced signaling features, LED Lighting,
Duress Alarm and Open Door Signaling.
LED Lighting is an optional piece of equipment (sold separately) that
provides a light source when the safe is open.
The LED Lamp Option plugs into a two (2) pin port on the side
of the lock.
The LED Lamp Option consists of a pair of high intensity white
LED Lamps in a wired housing that can be attached to the safe
in an appropriate position to provide light inside the safe when it
is open.
The LED Lamp Option must be turned ON to operate. See
Programming.
The LED Lamp will turn on when the lock is opened, and remain
on for 30 seconds (until the lock goes to sleep). If you press any
keypad buttons, the light will turn on again for another 30 sec-
onds. A key-press while the lights are on will restart the 30 sec-
ond shut-off timer.
Use of the LED Lamp Option will diminish the cycle life of the bat-
teries by some factor, depending on use frequency and duration.
5