Bosch 6 Series Gebrauchsanweisung - Seite 16

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Trockner Bosch 6 Series herunter. Bosch 6 Series 48 Seiten. 2 door top freezer, inox-easyclean
Auch für Bosch 6 Series: Benutzerhandbuch (24 seiten), Handbuch für Installation und Gebrauch (20 seiten), Handbuch für Installation und Gebrauch (20 seiten), Handbuch für Installation und Gebrauch (20 seiten), Gebrauchsanweisung und Installationsanleitung (48 seiten), Gebrauchsanweisung (16 seiten), Installationsanleitung Handbuch (27 seiten), Gebrauchsanweisung (12 seiten), Installations- und Betriebsanleitung (36 seiten), Gebrauchsanweisung (16 seiten), Handbuch für Installation und Gebrauch (16 seiten), Gebrauchsanweisung Handbuch (29 seiten), Benutzerhandbuch und Installationsanleitung (16 seiten), Informationen zur Verwendung (32 seiten), Kurzreferenz-Handbuch (2 seiten), Kurzreferenz-Handbuch (2 seiten), Informationen zur Verwendung (28 seiten), Benutzerhandbuch (23 seiten), Gebrauchsanweisung (24 seiten), Montage- und Gebrauchsanweisungen (24 seiten), Informationen zur Verwendung (16 seiten), Benutzerhandbuch (36 seiten), Benutzerhandbuch (32 seiten), Benutzerhandbuch (28 seiten), Benutzerhandbuch (28 seiten), Gebrauchsanweisung (28 seiten), Informationen zur Verwendung (20 seiten), Gebrauchsanweisung (28 seiten)

Seite drucken
Bosch 6 Series Gebrauchsanweisung

Trouble shooting

en
3Trouble shooting
I f a fault occurs, there is often a simple explanation.
T r o u b l e s h o o t i n g
Before calling the after-sales service, please refer to the
fault table and attempt to correct the fault yourself.
If a dish does not turn out exactly as you wanted,
Tip:
refer to the following chapter, where you will find lots of
tips and notes relating to the optimum
Fault table
Fault
The appliance is not working
Three zeros are lit on the display.
The appliance is not operating. A
cooking time is shown on the display.
The microwave is not working.
It is taking longer than usual for food
to heat up
The turntable is making a scraping or
grinding noise.
The microwave has stopped for no
apparent reason.
An
i
is shown on the display.
Error message "E - 3"
--------
16
Possible cause
The plug is not plugged into the mains
Power failure
The circuit breaker/fuse is faulty
Faulty operation
Power failure
The rotary selector has been accidentally turned.
The "start" button has not been pressed after the set-
ting was applied.
The door has not been properly closed.
The "start" button has not been pressed.
The microwave power output has been set too low.
A larger amount of food than usual has been placed in
the appliance.
The food was colder than usual.
Dirt or debris in the area around the turntable drive.
The microwave has a fault.
The appliance is in demo mode
Fault in automatic door opening system.
settings.~ "Tested for you in our cooking studio"
on page 18
:
Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Remedy/information
Connect the appliance to the electricity supply
Check whether other kitchen appliances are working
Check in the fuse box to make sure that the circuit
breaker/fuse for the appliance is in working order
Switch off the circuit breaker/fuse for the appliance in
the fuse box and switch it back on after approximately
10 seconds
Reset the time.
Press the "stop" button.
Press the "start" button or cancel the setting by press-
ing the "stop" button.
Check whether food remnants or debris is/are
trapped in the door.
Press the "start" button.
Select a higher microwave power setting.
Double the amount – double the time.
Stir or turn the food during heating.
Clean the roller ring and the recess in the cooking
compartment.
If this fault recurs, please call the after-sales service.
Deactivate demo mode.
~ "Basic settings" on page 14
If an error message is displayed, switch the appliance
off and on again; if the message disappears, it was a
one-off problem. If the fault occurs again or the error
message is still displayed, please contact the after-
sales service and provide the fault code.