Bosch 6 Series Instruction Manual - Page 16

Browse online or download pdf Instruction Manual for Dryer Bosch 6 Series. Bosch 6 Series 48 pages. 2 door top freezer, inox-easyclean
Also for Bosch 6 Series: User Manual (24 pages), Instructions For Installation And Use Manual (20 pages), Instructions For Installation And Use Manual (20 pages), Instructions For Installation And Use Manual (20 pages), Instruction Manual And Installation Instructions (48 pages), Instruction Manual (16 pages), Installation Instructions Manual (27 pages), Instruction Manual (12 pages), Installation And Operating Instructions Manual (36 pages), Instruction Manual (16 pages), Instructions For Installation And Use Manual (16 pages), Instructions For Use Manual (29 pages), User Manual And Installation Instructions (16 pages), Information For Use (32 pages), Quick Reference Manual (2 pages), Quick Reference Manual (2 pages), Information For Use (28 pages), User Manual (23 pages), Instruction Manual (24 pages), Installation Instructions And Instructions For Use (24 pages), Information For Use (16 pages), User Manual (36 pages), User Manual (32 pages), User Manual (28 pages), User Manual (28 pages), Instruction Manual (28 pages), Information For Use (20 pages), Instruction Manual (28 pages)

Print Page

Trouble shooting

3Trouble shooting

I f a fault occurs, there is often a simple explanation.

T r o u b l e s h o o t i n g

Before calling the after-sales service, please refer to the

fault table and attempt to correct the fault yourself.

If a dish does not turn out exactly as you wanted,

Tip:

refer to the following chapter, where you will find lots of

tips and notes relating to the optimum

Fault table

Fault

The appliance is not working

Three zeros are lit on the display.

The appliance is not operating. A

cooking time is shown on the display.

The microwave is not working.

It is taking longer than usual for food

to heat up

The turntable is making a scraping or

grinding noise.

The microwave has stopped for no

apparent reason.

is shown on the display.

Error message "E - 3"

--------

Possible cause

The plug is not plugged into the mains

Power failure

The circuit breaker/fuse is faulty

Faulty operation

Power failure

The rotary selector has been accidentally turned.

The "start" button has not been pressed after the set-

ting was applied.

The door has not been properly closed.

The "start" button has not been pressed.

The microwave power output has been set too low.

A larger amount of food than usual has been placed in

the appliance.

The food was colder than usual.

Dirt or debris in the area around the turntable drive.

The microwave has a fault.

The appliance is in demo mode

Fault in automatic door opening system.

settings.~ "Tested for you in our cooking studio"

on page 18

Warning – Risk of electric shock!

Incorrect repairs are dangerous. Repairs may only be

carried out and damaged power cables replaced by

one of our trained after-sales technicians. If the

appliance is defective, unplug the appliance from the

mains or switch off the circuit breaker in the fuse box.

Contact the after-sales service.

Remedy/information

Connect the appliance to the electricity supply

Check whether other kitchen appliances are working

Check in the fuse box to make sure that the circuit

breaker/fuse for the appliance is in working order

Switch off the circuit breaker/fuse for the appliance in

the fuse box and switch it back on after approximately

10 seconds

Reset the time.

Press the "stop" button.

Press the "start" button or cancel the setting by press-

ing the "stop" button.

Check whether food remnants or debris is/are

trapped in the door.

Press the "start" button.

Select a higher microwave power setting.

Double the amount – double the time.

Stir or turn the food during heating.

Clean the roller ring and the recess in the cooking

compartment.

If this fault recurs, please call the after-sales service.

Deactivate demo mode.

~ "Basic settings" on page 14

If an error message is displayed, switch the appliance

off and on again; if the message disappears, it was a

one-off problem. If the fault occurs again or the error

message is still displayed, please contact the after-

sales service and provide the fault code.