Aleph XC-1XTUK Handbuch

Blättern Sie online oder laden Sie pdf Handbuch für Sicherheitssensoren Aleph XC-1XTUK herunter. Aleph XC-1XTUK 3 Seiten. Xc-1xt series. outdoor dual technology intrusion detector 40ft l x 56 w (12m x 17m)

Seite drucken

Description: XC-1XT provides unsurpassed wide area unsecured outdoor instruion detection.

Combining Microwave & PIR detection technologies the XC-1XT ensures excellent coverage without

nuisance alarms. Dual outputs allow the use of a single detector for annunciation and security,

or allow multiple functioning via different control device assignments.

Installation:

For best results install the XC-1XT at a mounting height between 6.6 ft.(2.0m) and 8.2 ft. (2.5m). Mount the unit so it is

looking into an area free of obstructions, do not mount the unit so it is looking directly at heating or cooling sources. Avoid

viewing operating machinery or objects which have the potential for movement. Do not aim unit so it is looking at public

road / pathways.

Wire the XC-1XT to the control panel device using 18 to 24 AWG standard non-shielded wire, do not run wiring parallel to

AC wiring. Wiring should be in accordance with NEC, NFPA 70 for North America.

Prior to re-attaching front cover to unit; Set PIR sensitivity, PulseCount, LED Enable, Detection mode, and 50/60Hz

Flourescent Light immunity setting (Selectable Switch 1,2,3,4,5, and 6) as desired.

If the detector is viewing a narrow area, a PC setting of 4 should be avoided, as the small area may not allow enough

movement to detect intruders. A PC of "4" is best suited for a wide open detection area. For High Security applications set

PIR Sensitivity to "High Sensitivity" =(SW1 & 2 = 120% or 100%), this allows for a quicker detection at the edge of the

detection area.

XC-1XT.

potentiometer to adjust Microwave sensitivity (Preset @ 50%). A properly adjusted MW will detect crossing movement just

inside the protected area but not outside of the PIR coverage area.

SW-5 allow for the selection of Dual-Technology (MW & PIR) or PIR only detection modes. A PIR only detection mode is

useful when there is operating machinery or exposed fans always active within the protected area.

If the installation site is subject to severe vibrations (via close proximity to railroad tracks and /or large truck movement),

ensure that the mounting point is on a riged surface. In some situations it may be necessary to place a piece of plywood

between the mounting surface and the XC-1XT detector to buffer wall movement.

Walk-Test:

Once installation and initial setup is complete, perform a full walk test to insure that the detection parameters are met, if

required make control adjustments to fine tune detection characteristics. In order to insure detection quality, the XC-1XT

should be tested routinely, with no more than a one year period between tests.

Function Select Switch

SW-1 & 2 :PIR Sensitivity

120%

OFF

SW-1

SW-2

SW-3

SW-4 LED Enable

4 off - LED's Enabled

SW-4

4 on - LED's Disabled

SW-5

SW-5 Detection Mode

5 off - Dual (MW & PIR)

SW-6

5 on - PIR Only

SW-6 50/60 Hz

6 off - 60Hz

6 on - 50Hz

Switch ON

Switch OFF

XC-1XT SERIES

Outdoor Dual Technology Intrusion Detector

40FT L X 56 W (12m x 17m)

Animal Immunity characteristics are not available when a "High Sensitivity" setting is configured on the

Animal Immunity function is enabled by placing PIR Sensitivity at 60%. Use Microwave Sensitivity adjustment

100%

80%

60%

SW-3 Pulse Count

3 off - PC2

3 on - PC4

Tamper Switch

Control Layout and Configuration:

uW Module Do not Touch

PIR Detector Do not Touch

Terminal Configuration

TAMPER

ALARM 1

ALARM 2

NC NO C

NC NO

LED Indicators

Green = PIR

Red = Alarm

Amber = MW

Microwave Sensitivity

Adjustment

MIN.

MAX.

The Sensitivity Adjustment

allows for MW coverage to be

fine set to the protected area.

Preset = 50%

Max. = increases sensitivity

Min. = decreases sensitivity

SPARE

POWER