Dreamline Elegance Installationsanleitung Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Sanitärprodukt Dreamline Elegance herunter. Dreamline Elegance 14 Seiten. Shower door

Seite drucken

Flat head screws ST4.2×16 (15). Cover screw locations with Decorative covers (14). See

Fig 8 for details.

12. Repeat the step 11 for the Glass profile (4) and the Wall profile (5). See Fig 9 for details.

13. Open the glass door. Push the Bottom anti-water strip (11) onto the glass door. Push the

other Anti-water strip (10) into the groove of the Glass profile for glass door (2). See Fig

10 and Fig 11. Close the hole in the bottom pivot retainer with Flat socket head screw

M6×12 (19).

NOTE: You can also attach the pivot retainer to the tray or threshold using Flat head screw

ST4.2×30 (17).

NOTE: If your hardware has Oil Rubbed Bronze finish you will need to cover Bolt (L) with the

Screw cover (9). See Fig 12 for details.

14. Apply silicone sealant between the tray or threshold and the pivot bracket. Apply silicone

sealant over the Screw (17) or (19) to prevent leakage.

NOTE: The following steps (Steps 15-26) are only if your door requires the stationary

glass installation.

15. Locate the Stationary glass (22). Small hole on the short side of the stationary glass

should be on the bottom and away from wall.

If the thickness of your glass is 5/16" (8mm) place the U-shape seal gasket (30) on the

long (vertical) side of the glass panel. Push the Stationary glass (22) into the Glass

profile (4) groove using a hammer. See Fig 15A for details.

If the thickness of the glass is 3/8" (10mm), apply silicone sealant onto the groove of the

Glass profile (4). Push the stationary glass into the glass profile groove using a

hammer. See Fig 15B for details. （NOTE: If the stationary glass and the glass

profile have been assembled, you can skip this step.）

NOTE: Do not strike with bare hammer on the glass or metal profiles. Use piece of wood

between the hammer and profile.

16. Push the Glass profile (4) into the Wall profile (5) and push the Anti-water strip (31) onto

the Stationary glass (22) (Fig 15B/3 and Fig 16/1). Close the glass door against the Anti-

water strip (31) (Fig 16/2) to find the position of the Wall profile (5). (You can pull the

Glass profile from the Wall profile to adjust width). Mark the position of the Wall profile

on the wall.

17. Pull out the Glass profile with the Stationary glass inserted into it from the wall profile.

Use predrilled holes in the aluminum profile to mark holes for drilling. Now drill holes in the

wall and insert the Wall anchor (12) into the hole. Apply silicone sealant along the holes on

the wall. Attach the Wall profile (5) to the wall using Flat head screws ST4.2×30 (17). See

Fig 7/4,5,6,7,8 for details.

18. Push the Glass profile (4) with the Stationary glass and Anti-water strip (31) into the

Wall profile (5).

19. Adjust the width of your door by pulling out the Glass profiles (2) and (4) if it necessary for

size of your door. Adjust the Glass door using a level and tighten in place with the Socket

head screw M6×12 (18). See Fig 8/1,2.

Close the glass door and make sure that there is 1/16" - 1/8" gap between the glass door

and the Anti-water strip (31). See Fig 17/1.

20. Drill holes in Glass profile for glass door (2) through the Wall profile for glass door (1).

Secure the Wall profile for glass door (1) and the Glass profile for glass door (2) with

Flat head screws ST4.2×16 (15). Cover screw locations with Decorative covers (14). See

Fig 8/4,5,6 for details.

21. To adjust and secure the Stationary glass - Install the Bracket (29) onto the Stationary

glass; mark the drill hole for the bracket. Make sure the mark is clear and visible and drill

Rev. 1 .5