Bose Acoustic Wave Cannon System II Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Redner Bose Acoustic Wave Cannon System II herunter. Bose Acoustic Wave Cannon System II 2 Seiten.
Auch für Bose Acoustic Wave Cannon System II: Service-Handbuch (9 seiten), Kurzanleitung (2 seiten)

Seite drucken

Bose Acoustic Wave Cannon System II Schnellstart-Handbuch

AND OPERATING PROCEDURES. INCORRECT WIRING MAY RESULT IN

REFER TO YOUR INSTRUCTION MANUAL FOR PROPER INSTALLATION

MODE SWITCH GUIDE

DAMAGE AND/OR POOR PERFORMANCE.

POSITION

OPERATING MODE

RISK OF ELECTRICAL SHOCK

CAUTION

RISQUE DE CHOC ELECTRIQUE

AVIS

DO NOT OPEN

NE PAS OUVRIR

2-WAY WITH LOW FREQUENCY OPTION

(NOT USED)

STANDARD 2-WAY (WITH 502B)

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

VOICE ONLY/FULL RANGE (WITH 502A)

INPUT

HIGH

LOW

FREQ

LOW FREQ

MODE

OUTPUT

LEVEL

OUTPUT

INPUT LEVEL

OPT 4

OUTPUT MODE

–10

PIN 1 GRN

NC 3

PIN 1 GRN

SUM

NORM

PIN 1 GRN

PIN 2 +

–10

PIN 2 +

-18

PIN 2 +

CH 1

PIN 3 –

CH 2

CH 1

PIN 3 –

CH 2

CH 1/SUM

PIN 3 –

PROTECTED BY U.S. PATENT 3,038,964

INPUT B

220 V

CAUTION

In order to grant a secure operation do not mount the amplifier in

a fully closed housing. To preven electric shock, do not remove

cover. Disconnect power line in case of servicing.

ACHTUNG:

Um sichere Funktion zu gewährielsten, Gerät nicht in vollständig

geshlossenes Gehäuse einbauen. Abdeckung während des

Betriebes nicht entfernen. Bor Offnen des Gerätes Netzstecker

ziehen.

Bose Corporation, Framingham 01701, Mass, U.S.A.

Serial No.:

Made in Germany

Figure 1

results in very high continuous SPL

capability and superior low frequency

output without the need for external

limiters/compressors. The OC-1 is supplied

with a cable which is used to sense the

output voltage of the amplifier for AWCS II

system. The cable must be connected to

the four pin DIN connection on the rear

panel of the systems controller and the

amplifier output for the AWCS II system.

The system will automatically mute after

approximately one minute if this connec-

tion is not made.

System Configurations

The Bose

Acoustic Wave

Cannon

System II loudspeaker provides a flexible,

building-block approach to meet the sound

reinforcement requirements of a wide variety

of applications. You will find detailed

installation and system design guidelines

in the Bose

Acoustic Wave

System II Loudspeaker Owner's Guide.

Figure 1 shows three possible system

configurations: one AWCS II loudspeaker,

two 802

, 402

, or 502

loudspeakers,

and the appropriate systems controller.

Figure 2 shows the OC-1 option card to

be installed in the systems controller.

Figure 3 a, b, c shows the 402C, 502C

and 802C Series II systems controllers.

Figure 2

INPUT B

INPUT A

INPUT B

INPUT A

BRIDGE

220 V

MADE IN

USA

CAUTION

In order to grant a secure operation do not mount the amplifier in

a fully closed housing. To preven electric shock, do not remove

cover. Disconnect power line in case of servicing.

ACHTUNG:

230V

Um sichere Funktion zu gewährielsten, Gerät nicht in vollständig

geshlossenes Gehäuse einbauen. Abdeckung während des

50/60Hz 12W

Betriebes nicht entfernen. Bor Offnen des Gerätes Netzstecker

ziehen.

Bose Corporation, Framingham 01701, Mass, U.S.A.

Serial No.:

CH 2

Made in Germany

TÜV Rheinland

geprüdfte

Sicherheit

INPUT A

INPUT B

INPUT A

BRIDGE

MADE IN

USA

Figure 3a

Figure 3b

Cannon

Figure 3c

Architects' Specifications

The low frequency device shall be a light-

weight double barrel enclosure that uses

two waveguides as the acoustic vehicle.

The transducer shall consist of one (1)

woofer of 12" (30 cm) diameter, mounted

between the flanges that join the two

waveguides. The waveguide design of

the barrel shall limit cone excursion to

1" (.4 cm) p-p, to reduce distortion. The

operating frequency range shall be 25Hz

to 125Hz. The input connector, located on

the driver flange of the short barrel, shall

be 2-conductor spade lugs (barrier strips).

AWCS™II

802

402

™

502

402C Controller

502C Controller

802C II Controller

The maximum acoustic output of the

bass enclosure shall be 115dB-SPL

from 25Hz to 125Hz, with measurements

referenced to a full-bandwidth pink-noise

input at 1 meter at the enclosure's rated

power. Its power handling capacity shall

be 300 Watts continuous, referenced to

IEC noise for 100 hours.

The enclosure shall be made of custom

extruded polyvinyl chloride pipe. Outer

dimensions of the enclosure shall be 150"

(L) x 17" (W) (3.81 x .43 m); its weight

shall be 63 lb (29 kg).

The low-frequency device shall be the

Bose

Acoustic Wave

Cannon

System II loudspeaker.

The AWCS

II system shall be provided

with a separate system controller, to be

connected before the input(s) of the sys-

tem power amplifier(s). An OC-1 option

card, installed in the systems controller,

™

shall replace the bass active equalization.

The fixed, 2-channel system controller

shall provide active electronic equaliza-

tion and crossover functions. It shall in-

clude an operating mode switch, input

sensitivity switch, low-frequency output

level control, and mono sum switch. The

system controller shall use screw-type

terminal strips for balanced input and

output wiring connections. Outer dimen-

sion of the systems controller shall be

1.75" (H) x 19.0" (W) x 8.0" (D) (4.4 x

48.3 x 20.3 cm). It shall fit in the single

space of a standard 19" equipment

rack for mounting. Its weight shall be

5.5 lb (2.5 kg).

The electronic controller shall be the

Bose 402

C, 502

C or 802

systems controller.

Warranty Information

The Bose Acoustic Wave

System II (AWCS II) loudspeaker is

covered by a 5-year, transferable

limited warranty. The Bose 402C 502C

and 802C Series II systems controllers

are covered by a 2-year, transferable

limited warranty.

01701- 9168 USA JN94899 PN177920-Rev. 2

C Series II

Cannon