Bose Acoustic Wave Cannon System II Hızlı Başlangıç Kılavuzu - Sayfa 2
Konuşmacılar Bose Acoustic Wave Cannon System II için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Bose Acoustic Wave Cannon System II 2 sayfaları.
Ayrıca Bose Acoustic Wave Cannon System II için: Servis Kılavuzu (9 sayfalar), Hızlı Kılavuz (2 sayfalar)
AND OPERATING PROCEDURES. INCORRECT WIRING MAY RESULT IN
REFER TO YOUR INSTRUCTION MANUAL FOR PROPER INSTALLATION
MODE SWITCH GUIDE
DAMAGE AND/OR POOR PERFORMANCE.
POSITION
OPERATING MODE
RISK OF ELECTRICAL SHOCK
CAUTION
RISQUE DE CHOC ELECTRIQUE
AVIS
4
DO NOT OPEN
NE PAS OUVRIR
2-WAY WITH LOW FREQUENCY OPTION
3
(NOT USED)
2
STANDARD 2-WAY (WITH 502B)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
1
VOICE ONLY/FULL RANGE (WITH 502A)
INPUT
HIGH
LOW
FREQ
FREQ
LOW FREQ
MODE
OUTPUT
LEVEL
OUTPUT
.
0
INPUT LEVEL
INPUT LEVEL
OPT 4
OUTPUT MODE
–10
+4
PIN 1 GRN
NC 3
PIN 1 GRN
SUM
NORM
PIN 1 GRN
PIN 2 +
–10
+4
BA
2
1
PIN 2 +
-18
+3
PIN 2 +
CH 1
PIN 3 –
CH 2
FR
CH 1
PIN 3 –
CH 2
CH 1/SUM
PIN 3 –
PROTECTED BY U.S. PATENT 3,038,964
INPUT B
~
220 V
CAUTION
In order to grant a secure operation do not mount the amplifier in
a fully closed housing. To preven electric shock, do not remove
cover. Disconnect power line in case of servicing.
ACHTUNG:
Um sichere Funktion zu gewährielsten, Gerät nicht in vollständig
geshlossenes Gehäuse einbauen. Abdeckung während des
Betriebes nicht entfernen. Bor Offnen des Gerätes Netzstecker
ziehen.
Bose Corporation, Framingham 01701, Mass, U.S.A.
Serial No.:
Made in Germany
Figure 1
results in very high continuous SPL
capability and superior low frequency
output without the need for external
limiters/compressors. The OC-1 is supplied
with a cable which is used to sense the
output voltage of the amplifier for AWCS II
system. The cable must be connected to
the four pin DIN connection on the rear
panel of the systems controller and the
amplifier output for the AWCS II system.
The system will automatically mute after
approximately one minute if this connec-
tion is not made.
System Configurations
The Bose
®
Acoustic Wave
®
Cannon
System II loudspeaker provides a flexible,
building-block approach to meet the sound
reinforcement requirements of a wide variety
of applications. You will find detailed
installation and system design guidelines
®
in the Bose
Acoustic Wave
System II Loudspeaker Owner's Guide.
Figure 1 shows three possible system
configurations: one AWCS II loudspeaker,
two 802
®
, 402
TM
, or 502
TM
loudspeakers,
and the appropriate systems controller.
Figure 2 shows the OC-1 option card to
be installed in the systems controller.
Figure 3 a, b, c shows the 402C, 502C
and 802C Series II systems controllers.
Figure 2
INPUT B
INPUT A
INPUT B
INPUT A
BRIDGE
~
220 V
MADE IN
USA
CAUTION
In order to grant a secure operation do not mount the amplifier in
a fully closed housing. To preven electric shock, do not remove
cover. Disconnect power line in case of servicing.
ACHTUNG:
230V
~
AC
Um sichere Funktion zu gewährielsten, Gerät nicht in vollständig
geshlossenes Gehäuse einbauen. Abdeckung während des
50/60Hz 12W
Betriebes nicht entfernen. Bor Offnen des Gerätes Netzstecker
ziehen.
Bose Corporation, Framingham 01701, Mass, U.S.A.
Serial No.:
CH 2
Made in Germany
TÜV Rheinland
geprüdfte
Sicherheit
®
INPUT A
INPUT B
INPUT A
BRIDGE
MADE IN
USA
Figure 3a
Figure 3b
TM
®
TM
Cannon
Figure 3c
Architects' Specifications
The low frequency device shall be a light-
weight double barrel enclosure that uses
two waveguides as the acoustic vehicle.
The transducer shall consist of one (1)
woofer of 12" (30 cm) diameter, mounted
between the flanges that join the two
waveguides. The waveguide design of
the barrel shall limit cone excursion to
1" (.4 cm) p-p, to reduce distortion. The
operating frequency range shall be 25Hz
to 125Hz. The input connector, located on
the driver flange of the short barrel, shall
be 2-conductor spade lugs (barrier strips).
AWCS™II
®
®
802
®
402
™
502
402C Controller
502C Controller
802C II Controller
The maximum acoustic output of the
bass enclosure shall be 115dB-SPL
from 25Hz to 125Hz, with measurements
referenced to a full-bandwidth pink-noise
input at 1 meter at the enclosure's rated
power. Its power handling capacity shall
be 300 Watts continuous, referenced to
IEC noise for 100 hours.
The enclosure shall be made of custom
extruded polyvinyl chloride pipe. Outer
dimensions of the enclosure shall be 150"
(L) x 17" (W) (3.81 x .43 m); its weight
shall be 63 lb (29 kg).
The low-frequency device shall be the
Bose
®
Acoustic Wave
®
Cannon
System II loudspeaker.
The AWCS
TM
II system shall be provided
with a separate system controller, to be
connected before the input(s) of the sys-
tem power amplifier(s). An OC-1 option
card, installed in the systems controller,
™
shall replace the bass active equalization.
The fixed, 2-channel system controller
shall provide active electronic equaliza-
tion and crossover functions. It shall in-
clude an operating mode switch, input
sensitivity switch, low-frequency output
level control, and mono sum switch. The
system controller shall use screw-type
terminal strips for balanced input and
output wiring connections. Outer dimen-
sion of the systems controller shall be
1.75" (H) x 19.0" (W) x 8.0" (D) (4.4 x
48.3 x 20.3 cm). It shall fit in the single
space of a standard 19" equipment
rack for mounting. Its weight shall be
5.5 lb (2.5 kg).
The electronic controller shall be the
Bose 402
TM
C, 502
TM
C or 802
systems controller.
Warranty Information
The Bose Acoustic Wave
System II (AWCS II) loudspeaker is
covered by a 5-year, transferable
limited warranty. The Bose 402C 502C
and 802C Series II systems controllers
are covered by a 2-year, transferable
limited warranty.
© 1995 Bose Corporation, The Mountain, Framingham, MA
01701- 9168 USA JN94899 PN177920-Rev. 2
TM
®
C Series II
®
Cannon