Auber Instruments EZboil DSPR310D Gebrauchsanweisung - Seite 4

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Controller Auber Instruments EZboil DSPR310D herunter. Auber Instruments EZboil DSPR310D 14 Seiten. For step mashing and boiling process automation
Auch für Auber Instruments EZboil DSPR310D: Kurzanleitung (2 seiten)

Seite drucken

AUBER INSTRUMENTS

5.3.3 Keypad functions

If timer is disabled (tF = OFF), key A and B control the SSR power output. Press

key A momentarily to enable the output, or restart from the STOP status. The

bottom display will show "RUN" for a short moment. Press key B momentarily

to stop the output. The bottom display will flash "STOP".

If timer is enabled (tF = ON), key A and B control the SSR power output and

timer function. Press key A momentarily to enable the output, or resume/restart

from the HOLD/STOP status. If PuS is set to "dely" (delayed power-up, note 2-

2 in page 4), timer will be enabled at the same time. Press key B momentarily

to hold the timer, but it will NOT hold the power output status. Press and hold

Key B for 5 seconds to stop the timer and disable the power output. Bottom

display will flash "STOP" and OUT indicator is OFF.

Note for mute function of Key A/RUN: Key A can also be used to mute the

built-in buzzer when triggered by temperature alarm (relay mode ALbE only, note

12 in page 9). Once the built-in buzzer is turned on (triggered by temperature

alarm), user can mute the built-in buzzer manually by pressing Key "A" (or "RUN")

momentarily. This mute operation will not affect relay action nor mute step/timer

event alarm notifications.

Key A can be used to start the program as well, but "mute" function has higher

priority than "start" function: When process temperature is in the alarm zone and

the program has not started yet, press Key A momentarily will mute the alarm

first. To start the program, you need to press Key A again.

5.3.4 Criterions to start the timer in boiling mode

To start the timer, three criterions need to be met:

1). Timer must be enabled in parameter settings: tF = ON (note 9 in page 7)

2). The controller cannot be under STOP/HOLD status. If you see the display

flashes "STOP" or "HOLD", you need to press key A momentarily to start or

resume the program.

3). Controller's reading temperature (top display) must be higher than the value

of btsp (boiling timer start temperature, note 9 in page 7).

100

Press down

Knob

and hold the

knob for 5s

goto

mash

Knob

goto

prog

Knob

goto

boil

Knob

goto

rely

Knob

goto

syst

Figure 5. Parameter group selection

2018.08

Knob

Enter Mash

mode settings

Press

Rotate

Enter Step

Knob

Program

Settings (Mash

Press

mode)

Rotate

Knob

Enter Boil

mode settings

Press

Rotate

Knob

Enter Relay

settings

Press

Rotate

Knob

Enter System

settings

Press

Tip 1: When timer is started, you will hear the beeping notification. Please see

section 9 in page 10 for details.

Tip 2: Similar to mashing mode, you can even hold the timer (by pressing key B

momentarily) before the timer is started (reading temp. is below btsp, note 9 in

page 7). Then when reading temp. is over btsp, timer will be started and held

immediately. You will hear the beeping notification. This tip can create one

"HOLD" step before the timer is started.

6. Control Parameters

Parameters are divided into five groups (figure 5): MASH for step mashing

control, PROG for step program settings for mashing, BOIL for boiling control,

RELY for alarm relay settings and SYST for system configuration.

To enter parameter setting mode, press and hold the knob for at least 5s. Then

you will see "GOTO" on the top display. Rotate the knob, you will see the bottom

display changes with five different names: MASH (figure 5), PROG (figure 8),

BOIL (figure 10), RELY (figure 11) and SYST (figure 6). All parameter values

are stored in the controller memory, and they remain unchanged if you power it

off.

Press down and hold the knob for 5s to enter the setting group selection. Bottom

display is your current selected group. Press down the knob again to enter the

selected parameter group. Then top display shows the current selected

parameter name, and the bottom display shows its value/options. Rotate the

knob clockwise to increase the value, and counter-clockwise to reduce the value.

Fast rotating will change the value rapidly. Once finished, press knob again to

confirm and go to next parameter. You can press the knob repeatedly to exit the

setting quickly.

6.1 System settings (SYST)

System parameters that configure this controller are grouped under this menu.

Table 1. System configuration parameters.

System Configuration (SYST)

Display

Code

Description

Temp. reading offset

C-F

Temp. display unit

C-F

pus

PuS

Power up settings

Temperature

reading offset

Temp. display

unit

Power up

setting

End

Figure 6. Flow chart of setting system parameters.

WWW.AUBERINS.COM

Setting

Initial

Remark

Range

Setting

-20.0 ~

0.0

Note 1

+20.0 ° C or ° F

° C, ° F

° F

Note 2-1

inst, dely

dely

Note 2-2

goto

syst

Knob

C-f

Knob

pus

Dely

Knob

100

P4/14