elsner elektronik WS1000 Style Kurzanleitung

Blättern Sie online oder laden Sie pdf Kurzanleitung für Kontrolleinheit elsner elektronik WS1000 Style herunter. elsner elektronik WS1000 Style 2 Seiten. Connect control system
Auch für elsner elektronik WS1000 Style: Erste Schritte (2 seiten), Erste Schritte (2 seiten), Handbuch (2 seiten), Montageanleitung (2 seiten), Handbuch (20 seiten), Kurzanleitung (2 seiten)

Seite drucken

elsner elektronik WS1000 Style Kurzanleitung

Brief Instruction

Mounting of WS1000 Style

Item numbers 60201-60204, 60206-60209 (WS1000 Style),

60214 (WS1000 Style-10 PF)

The manual with additional information about commissioning,

functions and use of the controls WS1000 Style can be down-

loaded from www.elsner-elektronik.de in the menu area "Ser-

vice/Downloads".

Warning, mains voltage! National legal regulations are to be

observed. Installation, inspection, commissioning and

troubleshooting of the device must only be carried out by a

competent electrician.

Notes on wireless equipment

When planning facilities with devices that communicate via radio, adequate radio

reception must be guaranteed. The range will be limited by legal regulation and

structural circumstances. Avoid sources of interference and obstacles between re-

ceiver and transmitter, that could disturb the wireless communication. Those

would be for example:

•

Walls and ceilings (especially concrete and solar protection glazing).

•

Metal surfaces next to the wireless participants (e. g. aluminium

construction of a conservatory).

•

Other wireless devices and powerful local transmitters (e.g. wireless

headphones), which transmit on the same frequency. Please maintain a

minimum distance of 30 cm between wireless transmitters for that reason.

Preparing the installation location

The device must only be installed and used in dry, interior

spaces. Avoid condensation.

Cut-out dimensions for concealed box:

W = 248 mm +1 -0 | H = 165 mm +1 -0 | D = 84 mm

An external antenna can be connected in order to improve wireless communicati-

ons. During installation, a conduit 50 cm in length should be placed beneath the

recessed housing, in which the external antenna can be mounted (antenna dimen-

sions approx. 565 x 8 x 5, L × W × H in mm):

Conduit angled diagonally dow-

Conduit angled vertically downwards (only

nwards (for cable access from

for cable access from above!)

above or below)

concealed

box

cable

45°

M16 conduit, 50 cm in length

Preparing for installation

The display unit is held by magnets. Re-

move the front part from the concealed

box.

Caution: The display is connected

with a flat-ribbon cable to the circuit

board in the concealed box.

Loosen the plug so that the display unit

can be removed.

Remove all parts of the transportation

lock/packing.

Wall-fitting

Cavity wall fitting

Assembling the control unit with concealed box

During electrical installation, please introduce all connection cables into the con-

cealed box through the lower or upper side wall. In the process, keep the individual

connection wires short to prevent long reserve loops.

After connecting the cables screw the security covering onto the concealed box.

The security covering must be fixed before the control is put

into operation! It prevents contact with current-carrying parts

cable

in the concealed box.

M16 conduit,

50 cm in length

By adjusting the mounting screws, the display unit will rest flat on the wall later

and be held by the magnets safely.

Connect the flat ribbon cable to the display and place the display unit on the con-

cealed box. The magnets must be attracted by the mounting screws considerably

and the display unit must rest tightly on the concealed box.

Mounting of WS1000 Style • Version: 30.06.2020 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250

Mounting of WS1000 Style

The security covering in the concealed

box is attached with four screws: Loosen

the screws and take off the security cover-

ing.

Remove the circuit board from the con-

cealed box to be installed a keep it in a

place where it is protected from dirt. It

may never be exposed to dust or mo-

isture!

Place the concealed box in the wall so that

the arrows point upwards.

For fitting, screw the cover (board) on to

the concealed box with the enclosed

screws.

Clamp the concealed box to the wall with

the four enclosed screws.

Upon delivery, the pouch containing the

oder

assembly screws can be found in the con-

trol unit's concealed box.

Adjust the screws of the magnetic moun-

ting with the enclosed template. Each of

the four screws must be adjusted individi-

ally in height.

When the edge of the template rests on

the wall surface (1), the template must

rest on the mounting screws as well (2).

Structure of the connector board WS1000 Style

1 Multifunctional output 1

(terminals 1-3)

(potential-free)

Multifunctional input 2

2 Multifunctional output 2 (pot.-free)

(terminals 4-6)

3 Multifunctional output 3 (pot.-free)

22 Weather station (terminals 1-2)

4 Multifunctional output 4 (pot.-free)

Wire assignment: red = 1, black = 2,

5 Outer conductor L1

yellow and white = not connected

6 Outer conductor L1

23*Multifunctional input 3

7-11Drive group 1-5

(terminals 3-5)

12-16Drive group 6-10

Multifunctional input 4

17 Mains connection

(terminals 6-8)

L/N/PE 230 V/50 Hz

24 Connector for flat-ribbon cable to

18 Wall button 1 (terminals 1-3)

front board

Wall button 2 (terminals 4-6)

25 Microfuse T6.3 A (Drive 1-5)

Wall button 3 (terminals 7-9)

26 Microfuse T6.3 A (Drive 6-10)

Wall button 4 (terminals 10-12)

27 Microfuse T630 mA

19 Wall button 5 (terminals 1-3)

28 Slot KNX interface

Wall button 6 (terminals 4-6)

Wall button 7 (terminals 7-9)

* Supply voltage indoor sensor possi-

Wall button 8 (terminals 10-12),

ble via MF inputs

20 Wall button 9 (terminals 1-3)

(No. 21, terminals 1(+), 2(-) | 4(+),

Wall button 10 (terminals 4-6),

5(-) and No. 23, term. 3(+), 4(-) | 6(+),

21*Multifunctional input 1

7(-)), max. 400 mA altogether.

Structure of the connector board WS1000 Style-PF