Gaggenau VE 260 934 Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Kochfeld Gaggenau VE 260 934 herunter. Gaggenau VE 260 934 4 Seiten. Glass ceramic cooktop
Auch für Gaggenau VE 260 934: Gebrauchsanweisung (16 seiten)

Seite drucken

Ú Installation instructions

Important notes

Read these instructions carefully and keep them in a safe place.

Safety during use can only be ensured if the appliance is fitted

correctly according to these installation instructions. The installer

is responsible for ensuring that the appliance operates perfectly at

the point of installation.

The appliance must be connected to the mains only by a licensed

and trained technician.

Before carrying out any type of work, turn off the electricity.

For installation, currently applicable building regulations and the

regulations of the local electricity supplier must be observed.

This appliance corresponds to appliance class 3 (for installation in

a kitchen unit). It must be fitted according to the installation

drawing. Observe the minimum distance to side walls or furniture

parts and to the rear wall.

This appliance is not intended for operation with an external timer

or an external remote control.

Preparing the furniture

The surrounding kitchen unit must be heat-resistant to at least

90 °C. The stability of the unit must be maintained after producing

the cut-out.

Produce the cut-out for one or several Vario appliances. Proceed

as shown in the installation sketch. The angle between the cut

surface and the worktop must be 90°.

After producing the cut-out, remove the shavings. Seal the cut

surfaces to make them heat-resistant.

Observe a minimum clearance between the appliance housing

and parts of the unit of 10 mm.

Protection against accidental contact from below must be

guaranteed after installation. If the underside of the appliance can

be touched after installation, an intermediate shelf must be fitted

that can only be removed using a tool. Observe a minimum

clearance between the appliance and the shelf of 10 mm.

When fitting several Vario appliances: allow for the additional

space required for the connecting strip VV 200. Appliances can

also be fitted in individual recesses, if a minimum clearance of

40 mm between the appliances is observed.

Electrical connection

Check the electrical installation system before connecting the

appliance. Make sure that the household installation has sufficient

fuse or circuit breaker protection. Check that the appliance has the

same voltage and frequency as the electrical installation system

(see rating plate).

The appliance corresponds to protection class I and may only be

operated with a protective earth connection.

The installation system must incorporate an all-pole isolating

switch with a contact gap of at least 3 mm. This must remain

accessible after installation.

Only a qualified electrician who takes the appropriate regulations

into account may connect or replace the mains connection cable.

Appliance without mains connection cable: Only connect as shown

on the connection diagram. If necessary, fit the copper bridge

supplied. Mains connection cable: Type H05 VV-F or higher rated.

Observe the minimum cross section. The yellow/green wire for the

PE connection must be 10 mm longer than the other wires on the

appliance side.

Do not kink or trap the mains connection cable.

Fitting the appliance

Mark the centre of the recess exactly. Fit the short mounting rail

to the front of the recess and the long mounting rail to the rear of

the recess. Make sure the lugs of the mounting rails lie on the

worktop. The centre marking on the mounting rails must be

precisely flush with the centre marking of the recess.

Note: when fitting the appliance in a stone worktop glue on the

mounting rails with a temperature-resistant two-component

adhesive (metal on stone).

Lower the appliance into the cut-out. The snap-in pins on the

appliance must lie exactly on the catch springs. Firmly press the

appliance into the cut-out. The pins on the appliance must snap

into the catch springs.

Special instructions for installation outdoors

Operate the appliance on a residual current device (RCD) with a

maximum tripping current of 30 mA.

The appliance corresponds to protection class I and may only be

operated with a protective earth connection.

Check the mains cable regularly for signs of damage. Do not use

the appliance if the mains cable is damaged.

The mains cable must be rated at least to H07RN-F-5G1,5.

The appliance must be fitted into a worktop. Prevent moisture from

penetrating.

The appliance must be protected from weather after use and

cooling down (e.g. with a cover).

Removing the appliance

Disconnect the appliance from the power supply. Push out the

appliance from below.

Caution!

Risk of damage! Do not lever out the appliance from above.