ADEMCO LYNX Benutzerhandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Sicherheitssystem ADEMCO LYNX herunter. ADEMCO LYNX 17 Seiten.
Auch für ADEMCO LYNX: Schnellstart-Handbuch (8 seiten), System Manual (14 seiten)

Seite drucken

INITIALIZES DOWNLOAD ID, SUBSCRIBER ACCOUNT No. FOR INITIAL DOWNLOAD: No entry required.

SELECT 1 OF 5 DEFAULT OPTION SETUPS. Enter 1-5 to select from default tables 1-5. Enter 0 to abort.

EXITS PROGRAMMING MODE AND PREVENTS RE-ENTRY by: Installer Code + 8+ 0 + 0.

If 98 is used to exit programming mode, you must press " " and "#" within 50 seconds of power up or

from exiting Programming mode to re-enter Programming mode.

EXITS PROGRAMMING MODE AND ALLOWS RE-ENTRY by: Installer Code + 8 + 0 + 0 or: Power-up,

then press " " and "#" within 50 seconds of power up or from exiting Programming mode.

After exiting Program mode, the system takes up to 1 minute to reset. To bypass the reset delay, press [#] + [0].

*56 ZONE PROGRAMMING PROCEDURE

Use this mode to program zone information. Press *56 while in programming mode.

NOTE: Entry of a number other than one specified will give unpredictable results.

ZONE NUMBER

Enter the 2-digit zone number to be programmed: • Zone 1 =

[*] = Continue

00 = exit zone programming mode;

upon exiting, the prompt "56" blinks; press [*] + any field number to go to that field.

ZONE TYPE

Enter the 2-digit zone type ( zt ) for this zone (see table of zone types on worksheet page 13).

[*] = Continue

[#] = Return to previous prompt

REPORT CODE

Enter the report code ( rc ) for this zone.

Report consists of 2 hexadecimal digits, each of which consist of 2 numerical digits (A = 10, B = 11, C =

12, D = 13, E = 14, F = 15; see Report Code description on page 6 for explanation of codes).

[*] = Continue; If this is zone 1, the system skips to the VOICE DESCRIPTOR prompt (1C)

[#] = Return to previous prompt

INPUT TYPE

Enter the input type ( i ) for the transmitter assigned to this zone as follows:

3 = Supervised RF (RF)

4 = Unsupervised RF (UR)

5 = Button type (BR)

LOOP NUMBER

Enter the loop number ( l ) for this zone. If "L" is displayed, the serial number for this transmitter has

already been entered. You can keep the serial number and skip to the VOICE DESCRIPTOR prompt, or

you can continue to the DELETE SERIAL NUMBER prompt.

0 + [*] = to Delete Serial Number prompt (F)

[*] = Continue to the ENROLL MODE prompt (1A) if not enrolled, or VOICE DESCRIPTOR prompt (1C) if

already enrolled.

[#] = Return to previous prompt

DELETE SERIAL NUMBER/ZONE PARAMETERS

0 = Keep existing number and proceed to VOICE DESCRIPTOR prompt (1C)

1 = Delete the RF zone serial number only and return to the ZONE NUMBER prompt (A).

2 = Delete the RF zone serial number and all other zone parameters (zone type, report code, etc.), then

return to ZONE NUMBER prompt (A).

For non-RF zones, entering 1 or 2 deletes all zone parameters.

ENROLL MODE

0 = Skip to the VOICE DESCRIPTOR prompt (1C). If zone type is "00," then skips to DELETE SERIAL

NUMBER prompt instead.

1 = Enroll now and proceed to SERIAL NUMBER prompt (1b)

SERIAL NUMBER

Enter the transmitter's 7-digit serial number (printed on the transmitter). If you enter an incorrect digit,

press the [#] key to backup to that digit and reenter the correct digit.

When all 7 digits are entered, press the [*] key. Each digit will be re-displayed, and the keypad will beep

once for digits 1-6, 3 times for the last digit. If less than 7 digits are entered, the un-entered digits will

display "F." If too many digits have been entered, the first 6 digits will be saved, along with the last digit

that was entered (entering 123456789 yields serial number 1234569).

If the serial number is correct, press [*] again to save it and advance to the next prompt (1C) or, if the

zone type is 00, will return to the DELETE SERIAL NUMBER PROMPT (F).

If the serial number is not correct, press [#], which deletes the number and returns to the ENROLL MODE

prompt (1A), allowing you to reenter the number.

hard wire zone

• Zones 2-25 = RF transmitter zones

• Zone 26-41 = RF button zones

[*] = Continue

[#] = Return to previous prompt

8 –

–