ADEMCO Vista 4120 Installationsanleitung Handbuch - Seite 9

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Sicherheitssystem ADEMCO Vista 4120 herunter. ADEMCO Vista 4120 18 Seiten.

Seite drucken

WIRING CONNECTIONS

MOUNTING THE No. 4127

CONSOLE(S)

(See Summery of Connoetfons Dlmgmm)

Important:

Do not connect the battery or plug in the AC

transformer until all other wiring connections have been

completed. When pownrbrg up the systsm, ysu must uas

tb foIlswIng ssqusnssz

1. Plug in transformer.

2. Connect the batten.

Grounding

the System

In order for the protective devices in this product to be effective,

Terminal 21 must be terminated in a good earth ground. The

following are examples of good eanh grounds available at most

installatiins:

Metal Cold Water Pipe: Use a noncorrosive metal strap firmly

secured to the pipe to which the ground lead is electrically

connected and secured.

AC Power Outlet Ground: Available from 3 prong, 125VAC.

power outlets only. To test the integrity of the ground terminal,

use a three-wire circuit tester with neon lamp indiirs,

such as

the UL-Listed Ideal Model 61935, or equivalent, available at

most ebctrbal supply stores.

Separate the consob from its bad@ate by removal of the two

screws on the tap and bottom edges.

Use the backplate to mark the positions on the wall for the

screw mounting holes and the cutout fqr the interface wiring.

Use wall anchors for the screws and make the cutout in the

wall no larger than indicated on the template. The backplate is

designed to be directly mounted to either a single or double

gang ebctrbal bow.

Pull the interface wiring in the wall through the cut-out.

Pass the interface wiring through the opening in the ba&plate

and then mount backplate to the wall surface with screws.

Splice the interface wiring to the console wires. Insulated

solderless wire splices (such as Ademco No. 311) may be

used for splicing.

Attach the main body of the console to the wall-mounted

bsckplate. The oonsole is properly attached when it is screwed

tothebackp&ebytopandbottomscrews.

PROGRAMMING

THE SECURITY CONTROL

Installer options are stored in non-removable, electrically'

erasable, non-volatile EEROM memory. 'These options must

be programmed for the particular installation to establish its

specifii alarm and repolting features. The security control may

be programmed from a remote console.

When pmgramming, the field number will be displayed on the

LCD diiy;

also. each entry is displayed as it is keyed in. After

programming, values that have been entered in each fiikt can

berevbwedand,il

necessary, mod&d.

*Note: It Is possibb to program the system at any time - even

at the installeti premises prior to the actual installation.

Simply apply power temporarily to the control and then

program the unit as desired.

When programming from the consoles note the folbwing:

1. Enter the -ramming

mode by simultaneously depressing

the r] and [W] keys wlthout 30 ssoonds after power Is

rpplbd

to the Control, or subsequently by keying the code

4+1+2+Ofolknr&bvde~essionofCODE+O+Okevs.

Once an installer code & p&rammed, use it instead of ihe

default c#le (4120) to gain access to the programming mode.

2~secondsafterenlyintotheprogrammode.Wwillbe

displayed. Following the above display, the system is ready

to awept entrbs for Address 00.

3.To pmgram a data field, key [.I plus Addnu

(for example.

Ol), then make the required entry. To simply review a data

fiikf. key [a) plus Address.

4.When a data field has been completely programmed, the

console will 'beep' three times and then automatically

proceed to, and display. the next data field address to bs

programmed if that field is the next sequential address (if not,

key k] plus the address of the next field to be programmed.

5. II the number of diits that you enter in the data field is less

than the maximum permitted (for example, phone number),

then the console will display the last data entered. To

proceed, the next dsta fiild address to bs programmsd must

then be entered (for example. %5).

6. If an address Is bnproperly entered, the console will display

FC. II a program entry is improperly entered (for example, a

larger number than that which is permitted), the console

display will go blank. In either case, simply re-enter the

number.

ENTER

1. POWER UP, then depress p] and [#J

PROGRAMMING

simultaneously

within 30 seconds of

MODE:

powering up.

2. Initiilly, Key: 4 + 1 + 2 + 0 plus CODE

key+O+O.

3.After Installer Code is programmed.

key: Inataller Code + CODE key +O+O.

Notea: Type 3 method of re-entry to the pro-

EXm PROGRAM-

MING MODE:

l 99

giamming

mode is inhibited

if -the

programming mode is exited via use of

l a6.

Type 1 method of entry can always be

used, unless console program-ming has

been locked

out by the remote

downbader.

(always albws m-entry to program-ming

mode via Type 3 entry method above),

unless console programming has been

locked out by the remote downloader).

'98 (inhibits resntry to programming mode

via Type 3 entry method).

Note: When the programming mode is exited,

RESTORE

FACTORY DFLT

AfXANCE TOFIELD:

'96

[*]+ADDRESS (e.g., 01.10.21 etc)

PROGRAM FIELD:

ERASE FIELDS:

READ FIEU):

(*]+ACORES$folbvmd by dataenttfg

(.]+ADDRESS+[.]

(only applies to

Addresses 31 thru 35).

[#I + ADDRESS

SPECfAL MESSAGES

OC = OPEN CIRCUlT (no communicatiin between the Console

and the Control).

FC I FtELD CODE ERROR (program entry m'&ake, reenter

the data).

NOTE: The following programming information contains the

factory default settings within the brackets [ 1.

a 1 minute set-up period must elapse

before the system can properly function.