ADENDORFF MAC AFRIC SDRILC-024 Original Betriebsanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Original Betriebsanleitung für Bohrhammer ADENDORFF MAC AFRIC SDRILC-024 herunter. ADENDORFF MAC AFRIC SDRILC-024 11 Seiten. Cordless brushless rotary hammer

GENERAL POWER TOOL SAFETY WARNINGS
(For All Power Tools)
WARNING! Read and understand all instructions.
instructions listed below may result in electric shock, fire and/or serious
personal injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work Area Safety
1.
Cluttered or dark areas invite accidents.
Keep work area clean and well lit.
2. Do not operate power tools in explosive atmospheres, such as in the presence of
Power tools create sparks which may ignite the dust or
flammable liquids, gases, or dust.
fumes.
3. Keep children and bystanders away while operating a power tool.
you to lose control.
Electrical Safety
4. Power tool plugs must match the outlet. Never modify the plug in anyway. Do not use any
adapter plugs with earthed (grounded) power tools.
outlets will reduce risk of electric shock.
5. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators.
There is an increased risk o electric shock if your body is earthed or
grounded.
6. Do not expose power tools to rain or wet conditions.
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts.
cords increase the risk of electric shock.
8. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
Failure to follow all
Distractions can cause
Unmodified plugs and matching
Water entering a power tool will
Damaged or entangled
9. If operating a power in a damp location is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
NOTE: The term "residual current device (RCD)" may be replaced by the term "ground
fault circuit interrupter (GFCI)" or "earth leakage circuit breaker (ELCB)".
Personal Safety
10. Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol,
or medication.
A moment of inattention while operating power tools may result in serious
personal injury.
11.
Use personal protective equipment. Always wear eye protection.
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
12. Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and /or battery, picking up or carrying the tool.
your finger on the switch or energising power tools that have the switch on invites
accidents.
13. Remove any adjusting key or wrench before turning the tool on.
attached to a rotating part of the power tool may result in personal injury.
14. Do not overreach. Keep proper footing and balance at all times.
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and
Loose clothes, jewellery or long hair can be caught in
gloves away from moving parts.
moving parts.
16. If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used.
dust-related hazards.
Power Tool Use and Care
17. Do not force the power tool. Use the correct power tool for your application.
power tool will do the job better and safer at the rate for which it was designed.
18.
Do not use tool if switch does not turn it on or off.
Protective equipment
Carrying power tools with
A wrench or a key left
This enables better control
Use of dust collection can reduce
The correct
Any power tool that cannot be