Autonics PSQ-C01 Series Datenblatt - Seite 12

Blättern Sie online oder laden Sie pdf Datenblatt für Messgeräte Autonics PSQ-C01 Series herunter. Autonics PSQ-C01 Series 14 Seiten. Dual lcd display digital pressure sensor

Seite drucken

PSQ Series

Output type change

Output type for OUT1 and OUT2 can be able to set Nor-

mally Open or Normally Closed.

※ Note that Normally Open and Normally Closed provide

opposite output.

OUT1 output

Normally Open

Normally Closed

Normally Open

1O2O

Normally Open

1O2C

Normally Closed

1C2O

Normally Closed

1C2C

Response time (chattering prevention)

It can prevent control output from chattering by changing

response time.

There are 10 types of response time; 2.5ms, 5ms, 10ms,

25ms, 50ms, 100ms, 250ms, 500ms, 1,000ms, 5,000ms.

If the response time is getting longer, the detection will be

more stable by increasing the number of digital filter.

PV display color and color linked output

You can select PV display color to the linked output status.

There are 4 types as below.

Select color linked output among [OUT1], [OUT2], or [ALL].

PV display color

Green in normal status. When the set color linked output

R-ON

turns ON, it displays red.

Red in normal status. When the set color linked output

G-ON

turns ON, it displays green.

Red is fixed.

RED

Green is fixed.

GREN

Pressure unit change

PSQ series has 8 kinds of pressure unit.

Please select the proper unit for application.

• kPa, MPa, kgf/cm

, bar, psi, mmHg, inHg, mmH

※ When using mmH

O unit, multiply display value by 100.

SV display part

Select the display type at the SV display part in RUN mode.

There are 3 types; displaying SV [STD], displaying unit

[UNIT], none [OFF]

RESET

This function is to reset all parameters as factory default

except control output SV to prevent wrong settings or

difficult operation.

Password

This function is to limit parameter settings, to check the

parameter or to change the parameter settings only for

entering the set password.

• 0000: Password function OFF

• 0001: Only checking parameters

• Setting range: 0002 to 9999

G-20

OUT2 output

OFF

Normally Open

Normally Closed

Normally Open

Normally Closed

Control output change

Select between NPN open collector output or PNP open

collector output.

Key lock

The key lock function prevents key operations so that

conditions set in each mode.

ᆞPress the

key over 1 sec in RUN mode to lock

keys. The PV display part displays [LOCK], and the SV

display part displays [ON] for 1 sec and it returns in RUN

mode.

ᆞPress the

key over 1 sec in RUN mode to unlock

keys. The PV display part displays [LOCK], and the SV

display part displays [OFF] for 1 sec and it returns in

RUN mode.

Zero-point adjustment

The zero-point adjustment function forcibly sets the

pressure value to "zero" when the pressure port is opened

to atmospheric pressure. When the zero adjustment is

applied, analog output [Voltage or Current] is changed by

this function.

To set zero atmospheric pressure forcibly,

press the

keys over 1 sec in RUN mode with the

opened pressure port.

High/Low Peak Hold

This function is to diagnose malfunction of the system

caused by parasitic pressure through memorizing input the

max./min. pressure occurred from the system.

Press the

key more than 1 sec in RUN mode and set

the

Peak Hold.

Error and troubleshooting

Display Cause

When adjusting zero point

while external pressure is

ERR1

input.

When over current is

ERR2

applied on control output

When the range of Auto

sensitivity setting mode

ERR3

ST1, ST2 is set incorrectly.

When connection between

master and slave is wrong

ERR4

during copying parameters.

When entering invalid

ERR5

password.

When applied pressure

exceeds the high-limit of

HHHH

display pressure range.

When applied pressure

exceeds the low-limit of

LLLL

display pressure range.

When the correction value

of auto shift, remote zero

-HH-

exceeds the high-limit of

the setting range.

When the correction value

of auto shift, remote zero

-LL-

exceeds the low-limit of the

setting range.

-HL- When [HH], [LL] occur both.

Troubleshooting

Try again after removing

external pressure.

Remove the over current

conditions by adjusting load

resistance.

Check the setting range and

set ST1, ST2.

Check the cables between

sensors and the connection

of the same models.

Enter valid password.

Apply pressure within the

display pressure range.

Set the correction value

of auto shift, remove zero

within the setting range.