Autonics BWP20-12 Schnellstart-Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Sicherheitssensoren Autonics BWP20-12 herunter. Autonics BWP20-12 5 Seiten.
Seite drucken
Cautions during Installation
• Be sure to install this product by following the usage environment, location, and
specified ratings. Consider the listed conditions below.
- Installation environment and background (reflected light)
- Sensing distance and sensing target
- Direction of target's movement
- Feature data
• If the installation environment has reflected light from the wall or floor, a interval
distance of at least 0.3 m is required.
• When installing multiple sensors closely, it may result in malfunction due to mutual
interference. Install it by referring to the interference protection and the installation
method in the manual.
• Do not use in places where the light-receiving sensor is exposed to direct sunlight or
where the ambient illumination is higher than the specification.
• Do not impact with a hard object or bend the cable excessively. That could decrease
the product's water resistance.
• Use this product after the test. Check whether the indicator works appropriately for
the positions of the detectable object.
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.
BWP 20
-
❶
❷
❶ Number of optical axes
Number: Number of optical axes
Product Components
• Product
Sold Separately
• Flat bracket (BK-BWP-ST)
• Protection bracket (BK-BWP-P□)
Connections
0 V
+V
Blue
Brown
■ NPN open collector output
Blue
12 - 24 VDCᜡ
Brown
Black
White
White
Brown
Black
LOAD
OCP
SCP
Blue
• If the receiver OUT (black) line and the emitter JOB (black) line are not connected each other, the job indicator
of the emitter is not operated and maintains the light status.
• OCP (over current protection), SCP (short circuit protection)
Setting Switch
Switch
No.
Function
Selection of transmission
①
ON OFF
frequency
④
②
Selection of Light ON / Dark ON Dark ON
③
Selection of ON / flashing for
②
③
Job indicator
①
Selection of JOB / TEST
④
❷ Control output
No-mark: NPN open collector output
P: PNP open collector output
• Instruction manual
• L-shaped bracket (BK-BWP-L)
JOB (emitter) /
White SYNC
Black
OUT (receiver)
■ PNP open collector output
Blue
12 - 24 VDCᜡ
Brown
Black
White
White
Brown
OCP
SCP
Black
Blue
Setting
ON
OFF
Frequency B
Frequency A
Light ON
Flashing
ON
TEST mode
NORMAL mode
Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
• When installing, use M4 bolts for mounting screws and tighten with a torque of
2 N m or less.
Emitter
30
Job indicator (red)
Frequency B indicator (yellow)
Frequency A indicator (green)
Setting switch
2-Ø 4.2
Ø 3.5, 3 m
Model
BWP20-08(P)
BWP20-12(P)
BWP20-16(P)
BWP20-20(P)
Operation Timing Chart
■ Light ON mode
• In Dark ON mode, the waveforms are reversed.
Operation Indicator
ON
◑
●
OFF
◑◑
LOAD
Item
Power ON
Frequency A
operation
Frequency B
operation
TEST input
Stable light ON
Unstable light ON
Unstable light OFF -
Stable OFF
Flashing func. ON
Synchronous line
malfunction
Over current
• The operation of 'Operation indicator (red)', 'Job indicator (red)', 'Control output' is for Light ON, in case of
Dark ON, it is opposite operation against Light ON.
• Malfunction of synchronous line and over current, control output is OFF regardless of the mode.
Job indicator (red)
Operation indicator (red)
Stability indicator (green)
Sensing height (A)
B
140
180
220
260
300
340
380
420
ON Level
OFF Level
Flashing at 0.3 sec interval
Flashing simultaneously at
0.3 sec interval
Emitter
Receiver
Indicator
Indicator
Job
Green
Yellow
Green
Red
indicator
●
-
-
●
-
-
-
-
●
-
-
●
-
-
●
●
-
●
●
-
-
●
-
-
◑
●
-
-
-
-
◑
◑
Receiver
13
Product length (L)
190
270
350
430
Stable light ON area
Unstable light ON area
Unstable light OFF area
Stable light OFF area
ON
Stable indicator
OFF
(green)
ON
Operation indicator
OFF
(red)
ON
Job indicator
OFF
(red)
ON
Control output
OFF
Cross-flashing at 0.3 sec
interval
Control
Job
output
indicator
-
-
-
-
-
-
OFF
●
ON
●
ON
OFF
OFF
◑
OFF
OFF
OFF