KitchenAid 3185891 Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Kochfeld KitchenAid 3185891 herunter. KitchenAid 3185891 5 Seiten. 30" and 36" gas sealed burner glass cooktop

30" cooktop
30" min. base cabinet
is required. If cabinet has
a drawer, a 3-l/2" depth clearance from the
countertop to the top of the drawer (or other
obstruction)
in base cabinet is required.
36" Cooktop
36" min. base cabinet
is required.
If cabinet
has a drawer, a 3-l/2" depth clearance from the
countertop to the top of the drawer (or other
obstruction)
in base cabinet is required.
Fire Hazard
-I
Do Not obstruct
the flow of combustion
and ventilation
air.
Personal
Injury Hazard
Avoid installing
cabinet
storage
above the
cooking
surface.
If cabinets
are already
installed,
reduce the hazard of reaching
over a heated cooking
surface
by
installing
a range hood. The range hood
should
extend a minimum
of 5 inches out
from the bottom front of the cabinets.
Reaching
over a heated cooking
surface
could result in a serious
burn or other
personal
injury.
WARNING: If the information in this
manual is not followed exactly, a
fire or explosion may result
causing property damage, personal
injury or death.
Electrical
Shock Hazard
It is the customer's
responsibility:
l
To contact
a qualified
electrical
installer.
l
To assure that electrical
installation
is
adequate
and in conformance
with
National
Electrical
Code ANSI/NFPA
70
-
latest edition and all local codes
and ordinances.
- Do Not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.
- WHAT TO DO IF YOU SMELL
GAS
l
Do Not try to light any
appliance.
Failure to do so could result in fire, .
electrical
shock or other personal
mlury.
Take special
care when drilling
holes into
the wall for electrical
wiring.
Electrical
wires may be concealed
behind the wall
covering.
Failure to do so could result in fire,
electrical
shock or other personal
injury.
l
Do Not touch any electrical
switch; do not use any phone
in your building.
l
Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
supplier's instructions.
l
If you cannot reach your gas
supplier, call the fire
department.
For 30" cooktop - 30" min. cabinet width
above
C0ddOD
For 36" cooktbp
- 36" min. cabinet
width
w
above c0DMop
13" max.
upper
cabinet
+
depth
minimum
clearances
cabinet to countertop
1
countertop
\\
L
combustible
I
I
/
Do Not pinch the power
SUDDIV
A
I
l
Note: 30" min. when bottok
of ' /
wood
or metal cabinet is
cord beiween the'cooktop &i
cabinets.
protected
by not less than l/4"
flame retardant millboard
covered with not less than No.
28 MSG sheet steel, 0.015"
stainless steel, 0.024"
aluminum
or 0.020" copper.
Note: Clearances
specified are for combustible
walls and materials that have a density of 20 or
more pounds per cubic foot. No evaluation of
clearances
has been made for installations
adjacent to materials that are less than 20
unprotected wood or metal
sheet.
For new installations:
C
2-5/8" min. cabinet
space to backsplash
or
vertical
wall
2-310" min. space to
D
front edge of
countertop
S-114" min. cabinet
E
space both sides of
cooktop
from a
combustible
surface
Panel
A
'C
'D
E
2-5/a" min. cabinet
space to
backsplash
or vertical wall
2-318"
min. s ace to
front edge 0 P
countertop
4-518" min. cabinet
space both sides of
cooktop from a
combustible surface
I
I
pounds per cu. ft. or to plastic tiles and sheeting.
For replacement installations:
30" cooktop:
36" Cooktop:
18314" min., 20-518" max.
18-314" min., 2&S/8"
opening depth
opening
depth
I
26-112" min., 29518" max.
I
33" min., 34-710" max.
opening
width
opening width
I
Mobile
home installation
The installation of this cooktop must conform to the
Manufactured
Home Construction
and Safety
Standards, Title 24 CFR, Pat-l 3280 (formerly the
Federal Standard for Mobile Home Construction
and
Safety, Title 24, HUD Part 280); or when such
standard is not applicable,
the Standard for
Manufactured
Home Installations
1982
(Manufactured
Home Sites, Communities
and
Setups), ANSI A225, l/NFPA 501 A -
1987, or latest
edition, or with local codes.
Copies of the standards listed may be obtained from:
l
National
Fire Protection
Association
Batterymarch
Park
Quincy,
Massachusetts
02269
l
* American
Gas Association
1515 Wilson Boulevard
Arlington,
Virginia
22209
Before you start...
- Installation and service must
be performed by a qualified
installer, service agency or the
gas supplier.
Proper installation
is your responsibility.
Make sure
you have everything
necessary for correct
installation.
It is the responsibility
of the installer to
comply with the installation clearances
specified on
the serial/rating
plate. The serial/rating
plate can be
found on the bottom of the cooktop burner box.
Check location
where cooktop will be installed. The
location should be away from strong draft areas,
such
as
windows. The cooktop should be located for
convenient
use in the kitchen.
ALL OPENINGS
IN THE WALL OR FLOOR WHERE
THE COOKTOP
IS TO BE INSTALLED
MUST BE
SEALED.
Grounded
electrical
outlet is required. See
"Electrical requirements."
Proper gas supply
connection
must be available.
See "Gas supply requirements."
Countertop
opening
dimensions
that are shown
must be used. Given dimensions provide required 0"
clearance.
Cabinet construction:
This appliance
is designed
for use in a base cabinet with a depth of 24"
The
maximum depth for overhead cabinets is 13". The
minimum vertical clearance between the cooking
surface and the overhead cabinets is 30". Overhead
cabinets installed at either side of the appliance
must
be a minimum of 18" above the cooking surface. The
minimum distance between the front edge of the
countertop and the front edge of the cooktop is 3/4".
The minimum horizontal distance between the
overhead cabinets above the appliance are shown
for your model number.
New installations
follow minimum dimensions
given.
Replacement
installations
- Be sure that front
edge of cooktop is at least 1 -l/2" back from front
edge of countertop.
When installing
cooktop
over a built-under
oven.
Do Not fasten cooktop to countertop with clamps.
Cooktop then will be easy to remove if servicing is
ever necessary.
Note: The sealed gas cooktop is manufactured
for
use with NATURAL gas. Conversion to L.P. gas can
be made with Kit No. 4173627, available from your
KitchenAid dealer or authorized parts distributor.
Important:
Observe
all governing
codes and
ordinances.
Failure to meet codes and
ordinances
could lead to fire or electrical
shock.