KitchenAid 8285364 Installationsanleitung Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Kochfeld KitchenAid 8285364 herunter. KitchenAid 8285364 17 Seiten. 30" (76.2cm) and 36" (91.4 cm) electric built-in ceramic downdraft cooktop

Seite drucken

Electrical

requirements

If codes permit and a separate ground

wire is used, it is recommended that a

qualified electrician determine that the

ground path is adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you

are not sure cooktop is properly

grounded.

Do Not have a fuse in the neutral or

grounding circuit.

Installation

Remove shipping materials and tape

from cooktop.

The blower is set to vent straight out

the back of the cooktop.

To vent to the left side, right side or down

through the bottom of the cabinet, add an

elbow to the blower assembly exhaust vent.

The downdraft cooktop must be

connected to the proper electrical voltage

and frequency as specified on the

model/serial rating plate. The model/serial

rating plate is located on the bottom of the

cooktop.

A four-wire or three-wire, single-phase,

240-volt, 60-Hz, AC-only electrical

supply is required on a separate

30-ampere circuit, fused on both sides

of the line.

A time-delay fuse or circuit breaker is

recommended. The fuse size must not

exceed the circuit rating of the

appliance as specified on the

model/serial rating plate.

CONNECT WITH COPPER WIRE

ONLY.

Connected directly to the fused

disconnect (or circuit breaker box)

through flexible, armored or non-

metallic sheathed, copper cable (with

ground wire).

Flexible armored cable should connect

cooktop directly to the junction box.

Fuse both sides of the line.

It may be easier to connect appliance

cable to junction box before inserting

cooktop into cutout. See "Electrical

connections," Page 7.

WARNING

Excessive Weight Hazard

Use two or more people to move

and install cooktop.

Failure to do so could result in

back or other injury.

Lift entire cooktop up from cutout

when positioning cooktop in

countertop opening.

Insert downdraft cooktop into cutout.

Check that:

cooktop is centered in cutout.

front edge of downdraft cooktop is at least

1-1/2" (38.1 mm) from front edge of

countertop and parallel to countertop.

rear edge of cooktop is at least 3/4"

(19.1 mm) from rear wall as recommended.

side edge of cooktop is at least 6 inches

(15.2 cm) from side wall.

Locate the junction box to allow as

much slack as possible between the

junction box and cooktop so that the

downdraft cooktop can be moved if

servicing is ever necessary.

A U.L.-listed 1/2" (12.7 mm) conduit

connector must be provided at the

junction box.

The recommended minimum copper

wire size is No.-10 gauge. However,

wire sizes and connections must conform

to the requirements of the National

Electrical Code, ANSI/NFPA 70 — latest

edition*, or CSA Standards C22.1-94,

Canadian Electrical Code, Part 1 and 22.2

No. 0-M91 - latest edition** and all local

codes and ordinances. Wire sizes and

connections must conform with the rating

of the cooktop.

Copies of the standard listed may be obtained from:

* National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

** Canadian Standard Association

178 Rexdale Boulevard

Etobicoke, Ontario M9W 1R3

The wiring diagram is located on the

bottom of the cooktop.

Twist-on connectors and U.L.-listed 1/2"

(12.7 mm) conduit connector are not

provided.

Connect vent system. See "Venting

requirements," Pages 4-5. Use duct tape to

seal all joints. Vent must end with a wall or roof

cap outside the building.