Majorcom: NTU-200 Benutzerhandbuch - Seite 6
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Radio Majorcom: NTU-200 herunter. Majorcom: NTU-200 17 Seiten. Internet radio / dab / dab+ /
fm rds / usb reader
Auch für Majorcom: NTU-200: Benutzerhandbuch (20 seiten)
Seite drucken
10
NTU-200
Internet radio / DAB / DAB+ / FM RDS / USB reader
3
Getting started/setup
To set up the unit:
1. Place the unit on a suitable shelf or table
2. Connect the power adaptor between the unit and the mains supply.
3. To receive broadcast radio (DAB and FM), extend the telescopic antenna.
The setup wizard starts.
3.1
Setup wizard
When the unit is started for the first time, it runs
through a setup wizard to configure settings for
date/time and network. Once this has finished, the
system is ready to use in most modes.
Note: To change these settings later, select Menu >
System settings >. To run the setup wizard again,
select Menu > System settings > Setup wizard.
Select Yes to start the setup wizard.
If you choose No, the next screen asks if you would
like to run the wizard next time the unit is started.
The
system
then
starts
without
time/date and network settings and enters the Main
Menu.
Note: If power is removed while the wizard is in
progress, the wizard will run again next time
when the unit is started.
3.1.1
12/24 hour display
To change between 12 and 24 hour display, select Set 12/24 hour and then select your
preference.
3.1.2
Time/date
The time and date can be updated manually or automatically. With auto-update, the time
and date are automatically synchronized with external clocks. Auto-update is generally
more accurate.
Auto-update
Auto-update works with data sent over DAB, FM or
the Internet. The clock is only updated when in a
corresponding mode, so it is best to select a mode
you use regularly.
DAB and FM use time signals broadcast with radio
transmissions.
Network uses a time signal sent from the Frontier
Silicon Internet radio portal when in any network-
connected mode.
1. Select Update from DAB, Update from FM, Update from Network or No update.
2. If you are updating from the network, set your time zone.
3. If your country uses daylight saving, the automatically updated time from the network
may be wrong by one hour. When daylight savings are in effect (during the winter),
turn on the Daylight savings option to rectify this.
Note that if you are updating the time from DAB or FM, the Daylight savings option
User manual
5 6 , c h e m i n d e l a Fl a m b è r e · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
WELCOME
configuring
Internet radio / DAB / DAB+ / FM RDS / USB reader
has no effect on the clock's time.
The unit will auto-update from the selected source when time information is available.
Manual set
If you set No update, the wizard now prompts you to set the time and date manually.
The date and time are displayed as dd-mm-yyyy and
hh:mm AM/PM with the first value, dd, active
(flashing).
Adjust each value with the Select control. As each
value is set, the next value becomes active and
flashes.
3.1.3
Network
The unit is compatible with all common network protocols and encryption methods,
including Wi-Fi Protected Setup (WPS).
To connect the unit to your network, you need one of the following:
•
A wired router and an Ethernet (RJ45 network) cable
•
A Wi-Fi wireless router, together with password key if set
Select WLAN region/country > Wi-Fi network
(SSID), and then select a network from the list.
To connect to a wired network, select [Wired], after
ensuring that the Ethernet cable from the wired router
is connected to the Ethernet socket of the unit.
If the network is open (non-encrypted), the unit connects without any further ado; see
Completion below.
Standard encrypted network
To enter the network's key (password), use the
Select control to move the cursor through the
characters and select. As each character is
selected, the key is built up near the top of the
display.
There are three options accessible by turning
Select back before the first characters
(0123...) – Backspace, OK and Cancel.
WPS encrypted network
WPS encrypted networks are identified by
'[WPS]' at the start of the network name, and
have three methods of connection. Select one
and follow the prompts:
•
Push Button >
The unit prompts you to press the
connect button on the router. It then
scans for a ready Push Button
Connect network and connects.
5 6 , c h e m i n d e l a Fl a m b è r e · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
11
NTU-200
User manual