Majorcom: NTU-200 Руководство пользователя - Страница 6

Просмотреть онлайн или скачать pdf Руководство пользователя для Радио Majorcom: NTU-200. Majorcom: NTU-200 17 страниц. Internet radio / dab / dab+ / fm rds / usb reader
Также для Majorcom: NTU-200: Руководство пользователя (20 страниц)

Печатать страницу

NTU-200

Internet radio / DAB / DAB+ / FM RDS / USB reader

Getting started/setup

To set up the unit:

1. Place the unit on a suitable shelf or table

2. Connect the power adaptor between the unit and the mains supply.

3. To receive broadcast radio (DAB and FM), extend the telescopic antenna.

The setup wizard starts.

3.1

Setup wizard

When the unit is started for the first time, it runs

through a setup wizard to configure settings for

date/time and network. Once this has finished, the

system is ready to use in most modes.

Note: To change these settings later, select Menu >

System settings >. To run the setup wizard again,

select Menu > System settings > Setup wizard.

Select Yes to start the setup wizard.

If you choose No, the next screen asks if you would

like to run the wizard next time the unit is started.

The

system

then

starts

without

time/date and network settings and enters the Main

Menu.

Note: If power is removed while the wizard is in

progress, the wizard will run again next time

when the unit is started.

3.1.1

12/24 hour display

To change between 12 and 24 hour display, select Set 12/24 hour and then select your

preference.

3.1.2

Time/date

The time and date can be updated manually or automatically. With auto-update, the time

and date are automatically synchronized with external clocks. Auto-update is generally

more accurate.

Auto-update

Auto-update works with data sent over DAB, FM or

the Internet. The clock is only updated when in a

corresponding mode, so it is best to select a mode

you use regularly.

DAB and FM use time signals broadcast with radio

transmissions.

Network uses a time signal sent from the Frontier

Silicon Internet radio portal when in any network-

connected mode.

1. Select Update from DAB, Update from FM, Update from Network or No update.

2. If you are updating from the network, set your time zone.

3. If your country uses daylight saving, the automatically updated time from the network

may be wrong by one hour. When daylight savings are in effect (during the winter),

turn on the Daylight savings option to rectify this.

Note that if you are updating the time from DAB or FM, the Daylight savings option

User manual

5 6 , c h e m i n d e l a Fl a m b è r e · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7

F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r

WELCOME

configuring

Internet radio / DAB / DAB+ / FM RDS / USB reader

has no effect on the clock's time.

The unit will auto-update from the selected source when time information is available.

Manual set

If you set No update, the wizard now prompts you to set the time and date manually.

The date and time are displayed as dd-mm-yyyy and

hh:mm AM/PM with the first value, dd, active

(flashing).

Adjust each value with the Select control. As each

value is set, the next value becomes active and

flashes.

3.1.3

Network

The unit is compatible with all common network protocols and encryption methods,

including Wi-Fi Protected Setup (WPS).

To connect the unit to your network, you need one of the following:

•

A wired router and an Ethernet (RJ45 network) cable

•

A Wi-Fi wireless router, together with password key if set

Select WLAN region/country > Wi-Fi network

(SSID), and then select a network from the list.

To connect to a wired network, select [Wired], after

ensuring that the Ethernet cable from the wired router

is connected to the Ethernet socket of the unit.

If the network is open (non-encrypted), the unit connects without any further ado; see

Completion below.

Standard encrypted network

To enter the network's key (password), use the

Select control to move the cursor through the

characters and select. As each character is

selected, the key is built up near the top of the

display.

There are three options accessible by turning

Select back before the first characters

(0123...) – Backspace, OK and Cancel.

WPS encrypted network

WPS encrypted networks are identified by

'[WPS]' at the start of the network name, and

have three methods of connection. Select one

and follow the prompts:

•

Push Button >

The unit prompts you to press the

connect button on the router. It then

scans for a ready Push Button

Connect network and connects.

5 6 , c h e m i n d e l a Fl a m b è r e · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7

F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r

NTU-200

User manual