KitchenAid Briva Installationsanleitung Handbuch - Seite 5

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Geschirrspüler KitchenAid Briva herunter. KitchenAid Briva 6 Seiten. In-sink dishwasher

Seite drucken

Installation steps

Important:

If HOT WATER ACCESSORY TANK

Accessory Part No. 4396282 will be

used, the tank must be installed first.

cut along

back of

this corner

inner carton

With a utility knife, cut along the

back right corner of inner carton.

Remove inner carton. Leave

dishwasher on bottom pad and wood

frame.

Install faucet (not included). The

dishwasher is shipped ready for

installation of a one-hole faucet. If a

two-, three- or four-hole faucet is to be

installed, the holes must be added by

a qualified plumber according to the

faucet manufacturer's specifications.

1/4" bead of

silicone caulk

dishwasher

cutout

Mark countertop and apply a

1/4" bead of silicone caulk 1/4" away

from dishwasher cutout.

Important.

To prevent

damage to right-

hand hinge, open

dishwasher lid

BEFORE setting dishwasher

into countertop cutout.

WARNING

Excessive Weight Hazard

Use two or more people to move

and install dishwasher.

Failure to do so can result in back

or other injury.

Set the dishwasher into

countertop cutout. Make sure front

of dishwasher is parallel to front

edge of countertop.

Immediately remove any excess

caulking.

rail

countertop

Install two clamp brackets,

evenly spaced, on front, back and left

(sink) side clamp rails. Optional: If

space permits, install two clamp

brackets, evenly spaced, on the right

wood frame

side rail.

To install clamps:

• Hook upper clamp onto rail. Use

flat-blade screwdriver to attach

clamp to rail.

• Use 7/16" deep-well socket and

securely tighten nut against lower

clamp. Do not over tighten.

For installations that must be direct

wired, go to Step 7 below.

For installations using the factory-

equipped power supply cord, go to

Step 8 on next page.

DIRECT WIRE METHOD.

If dishwasher must be directly wired

to meet local codes, the power

supply cord must be removed and

dishwasher wired directly. Electrical

connections must be contained

within the terminal box and meet all

national and local codes and

ordinances.

IF POWER SUPPLY CORD IS

REMOVED, THE DISHWASHER

MUST BE CONNECTED WITH

COPPER WIRE ONLY.

Route direct wire so that it does not

touch lower part of dishwasher tub.

Electrical Shock Hazard

Disconnect electrical power at

the fuse box or circuit breaker

box before installing

dishwasher.

Failure to do so can result in

death or electrical shock.

upper

clamp

lower

clamp

WARNING

screws

GFCI

front panel

7A.

Remove 5 screws (2 each

side and above GFCI) holding the

metal front panel and remove panel.

terminal

box screw

7B.

Remove terminal box screw

and terminal box.

do not remove

this grommet

power

cord

green ground

wire

7C.

Remove power cord green

ground wire from under green

ground screw. Remove twist-on

connectors and disconnect black and

white wires. Do not reuse connectors.

locking

tab

power

cord

7D.

Use pliers and squeeze

locking tab in the power cord strain

relief grommet. Remove power cord

and grommet.

conduit

connector

7E.

Install a U.L.-listed conduit

connector in power cord hole.

terminal

box

green ground

screw