- ページ 5
食器洗い機 KitchenAid BrivaのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid Briva 6 ページ。 In-sink dishwasher
ページを印刷するInstallation steps
Important:
If HOT WATER ACCESSORY TANK
Accessory Part No. 4396282 will be
used, the tank must be installed first.
cut along
back of
this corner
inner carton
1.
With a utility knife, cut along the
back right corner of inner carton.
Remove inner carton. Leave
dishwasher on bottom pad and wood
frame.
2.
Install faucet (not included). The
dishwasher is shipped ready for
installation of a one-hole faucet. If a
two-, three- or four-hole faucet is to be
installed, the holes must be added by
a qualified plumber according to the
faucet manufacturer's specifications.
1/4" bead of
silicone caulk
dishwasher
cutout
3.
Mark countertop and apply a
1/4" bead of silicone caulk 1/4" away
from dishwasher cutout.
Important.
C
4.
R
I
S
To prevent
T
T
damage to right-
I
E
hand hinge, open
C
P
dishwasher lid
A
BEFORE setting dishwasher
L
into countertop cutout.
WARNING
Excessive Weight Hazard
Use two or more people to move
and install dishwasher.
Failure to do so can result in back
or other injury.
5.
Set the dishwasher into
countertop cutout. Make sure front
of dishwasher is parallel to front
edge of countertop.
Immediately remove any excess
caulking.
rail
countertop
6.
Install two clamp brackets,
evenly spaced, on front, back and left
(sink) side clamp rails. Optional: If
space permits, install two clamp
brackets, evenly spaced, on the right
wood frame
side rail.
To install clamps:
• Hook upper clamp onto rail. Use
flat-blade screwdriver to attach
clamp to rail.
• Use 7/16" deep-well socket and
securely tighten nut against lower
clamp. Do not over tighten.
For installations that must be direct
wired, go to Step 7 below.
For installations using the factory-
equipped power supply cord, go to
Step 8 on next page.
7.
DIRECT WIRE METHOD.
If dishwasher must be directly wired
to meet local codes, the power
supply cord must be removed and
dishwasher wired directly. Electrical
connections must be contained
within the terminal box and meet all
national and local codes and
ordinances.
IF POWER SUPPLY CORD IS
REMOVED, THE DISHWASHER
MUST BE CONNECTED WITH
COPPER WIRE ONLY.
Route direct wire so that it does not
touch lower part of dishwasher tub.
Electrical Shock Hazard
Disconnect electrical power at
the fuse box or circuit breaker
box before installing
dishwasher.
Failure to do so can result in
death or electrical shock.
upper
clamp
lower
clamp
WARNING
screws
screws
GFCI
front panel
7A.
Remove 5 screws (2 each
side and above GFCI) holding the
metal front panel and remove panel.
terminal
box screw
7B.
Remove terminal box screw
and terminal box.
do not remove
this grommet
power
cord
green ground
wire
7C.
Remove power cord green
ground wire from under green
ground screw. Remove twist-on
connectors and disconnect black and
white wires. Do not reuse connectors.
locking
tab
power
cord
7D.
Use pliers and squeeze
locking tab in the power cord strain
relief grommet. Remove power cord
and grommet.
conduit
connector
7E.
Install a U.L.-listed conduit
connector in power cord hole.
terminal
box
green ground
screw
5